Sony FX52 Operating Instructions - Page 46

Symptom, Cause and Remedy, Adjust the Contrast or Brightness in the PICTURE SETTING

Get Sony FX52 - VPL XGA LCD Projector PDF manuals and user guides
UPC - 027242684263
View all Sony FX52 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Symptom Cause and Remedy The picture from INPUT C connector is colored strange. • Setting for Input-C Signal Sel. in the SET SETTING menu is incorrect. c Select Computer, Video GBR or Component for Input-C Signal Sel. in the SET SETTING menu according to the input signal (see page 34). "Please check INPUT-C setting." appears in spite of inputting the correct signal from INPUT C. • Setting for Input-C Signal Sel. in the SET SETTING menu is incorrect. c Select Computer, Video GBR or Component for Input-C Signal Sel. in the SET SETTING menu according to the input signal (see page 34). On-screen display does not • Status in the MENU SETTING menu has been set to Off. appear. c Set Status in the MENU SETTING menu to On (see page 35). Color balance is incorrect. • Picture has not been adjusted properly. c Adjust the picture (see page 31). • Projector is set to wrong color system. c Set Color System in the SET SETTING menu to match the color system being input (see page 34). The picture is too dark. • Contrast or Brightness has not been adjusted properly. c Adjust the Contrast or Brightness in the PICTURE SETTING menu properly (see page 31). • The lamp has burnt or dims. c Replace the lamp with a new one (see page 42). The picture is not clear. • Picture is out of focus. c Adjust the focus (see page 24). • Condensation has occurred on the lens. c Leave the projector for about two hours with the power on. The image extends beyond the screen. • The APA key is pressed although there are black edges around the image. c Display the full image on the screen and press the APA key. c Adjust Shift in the INPUT SETTING menu properly (see page 33 ). The picture flickers. • Dot Phase in the INPUT SETTING menu has not been adjusted properly. c Adjust Dot Phase in the INPUT SETTING menu properly (page 33). Remote Commander Symptom Cause and Remedy The Remote Commander • The Remote Commander batteries are dead. does not work. c Replace with a new battery (see page 16). The menu display does not • The PJ/NETWORK select switch on the Remote Commander is appear even when you set to NETWORK. press the MENU key on the c Set the PJ/NETWORK select switch to PJ, then press the Remote Commander. MENU key. 46 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
46
Troubleshooting
Remote Commander
The picture from INPUT C
connector is colored
strange.
• Setting for Input-C Signal Sel. in the SET SETTING menu is
incorrect.
c
Select Computer, Video GBR or Component for Input-C Signal
Sel. in the SET SETTING menu according to the input signal
(see page 34).
“Please check INPUT-C
setting.” appears in spite of
inputting the correct signal
from INPUT C.
• Setting for Input-C Signal Sel. in the SET SETTING menu is
incorrect.
c
Select Computer, Video GBR or Component for Input-C Signal
Sel. in the SET SETTING menu according to the input signal
(see page 34).
On-screen display does not
appear.
• Status in the MENU SETTING menu has been set to Off.
c
Set Status in the MENU SETTING menu to On (see page 35).
Color balance is incorrect.
• Picture has not been adjusted properly.
c
Adjust the picture (see page 31).
• Projector is set to wrong color system.
c
Set Color System in the SET SETTING menu to match the color
system being input (see page 34).
The picture is too dark.
• Contrast or Brightness has not been adjusted properly.
c
Adjust the Contrast or Brightness in the PICTURE SETTING
menu properly (see page 31).
• The lamp has burnt or dims.
c
Replace the lamp with a new one (see page 42).
The picture is not clear.
• Picture is out of focus.
c
Adjust the focus (see page 24).
• Condensation has occurred on the lens.
c
Leave the projector for about two hours with the power on.
The image extends beyond
the screen.
• The APA key is pressed although there are black edges around the
image.
c
Display the full image on the screen and press the APA key.
c
Adjust Shift in the INPUT SETTING menu properly (see
page 33 ).
The picture flickers.
• Dot Phase in the INPUT SETTING menu has not been adjusted
properly.
c
Adjust Dot Phase in the INPUT SETTING menu properly
(page 33).
Symptom
Cause and Remedy
The Remote Commander
does not work.
• The Remote Commander batteries are dead.
c
Replace with a new battery (see page 16).
The menu display does not
appear even when you
press the MENU key on the
Remote Commander.
• The PJ/NETWORK select switch on the Remote Commander is
set to NETWORK.
c
Set the PJ/NETWORK select switch to PJ, then press the
MENU key.
Symptom
Cause and Remedy