Sony HDRC-4000 Operation Guide - Page 51

NETWORK menu, DIAGNOSIS menu, name, No., Set value, Meaning

Get Sony HDRC-4000 PDF manuals and user guides View all Sony HDRC-4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

NETWORK menu Use to configure network-related settings. Page name Page No. N01 Item IP ADDRESS(CH.A) IP ADDRESS(CH.B) SUBNET MASK DEFAULT GATEWAY SET MAC ADDRESS N02 AUTO NEGOTIATION CONNECTION SPEED DUPLEX MODE LINK CONDITION SET N03 CNS MODE Set value 0.0.0.0 to 255.255.255.255 0.0.0.0 to 255.255.255.255 0.0.0.0 to 255.255.255.255 0.0.0.0 to 255.255.255.255 ENTER to execute 00:00:00:00:00:00 to FF:FF:FF:FF:FF:FF OFF, ON 10M, 100M HALF, FULL UP, DOWN ENTER to execute LEGACY, BRIGDE, MCS MCS MODE REMOTE CONTROL NO CH.A CH.B MASTER IP ADDRESS (CLIENT) 0 to 96 0 to 96 0.0.0.0 to 255.255.255.255 TARGET IP ADDRESS(CH.A) TARGET IP ADDRESS(CH.B) SET 0.0.0.0 to 255.255.255.255 0.0.0.0 to 255.255.255.255 ENTER to execute DIAGNOSIS menu Displays the device status. Page name Page No. D01 Item SY DVP SDI DCP1 DCP2 Set value OK, NG OK, NG OK, NG OK, NG OK, NG Meaning IP address setting of unit (Set different IP addresses for channel A and channel B) Subnet mask setting (common to channels A and B) Gateway IP address setting (common to channels A and B) Apply the IP address, subnet mask, and default gateway settings in the menu to the unit MAC address of the unit (display only) LAN connection auto-negotiation function on/off setting LAN connection speed setting Switch LAN connection between half and full duplex mode LAN connection status (display only) Apply the auto-negotiation, connection speed, and half/full duplex settings to the unit Camera network system communications mode setting LEGACY: When connected with a command network unit (such as the CNU-700) or remote control unit (such as the RCP-3500/1500 series) via an 8-pin multi connector (excluding when unit is connected to camera network master device via LAN connection) BRIDGE: When connected 1-to-1 with remote control panel via LAN connection MCS: When connected to camera network master device, for example a master setup unit (such as the MSU-1000), via LAN connection (Display only) Number setting of device used for remote control (remote control is disabled when set to 0) IP address setting of the master device (enabled in MCS mode only) IP address setting of remote control panel in bridge connection (enabled in BRIDGE mode only) Apply the CNS mode, device number, master IP address, and target IP address settings in the menu to the unit Meaning Internal board status 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
51
NETWORK menu
Use to configure network-related settings.
DIAGNOSIS menu
Displays the device status.
Page name
Page No.
Item
Set value
Meaning
<IP ADDRESS
SETTINGS>
N01
IP ADDRESS(CH.A)
0.0.0.0
to 255.255.255.255
IP address setting of unit (Set different IP
addresses for channel A and channel B)
IP ADDRESS(CH.B)
0.0.0.0
to 255.255.255.255
SUBNET MASK
0.0.0.0
to 255.255.255.255
Subnet mask setting (common to channels A
and B)
DEFAULT GATEWAY
0.0.0.0
to 255.255.255.255
Gateway IP address setting (common to
channels A and B)
SET
ENTER to execute
Apply the IP address, subnet mask, and default
gateway settings in the menu to the unit
MAC ADDRESS
00:00:00:00:00:00 to
FF:FF:FF:FF:FF:FF
MAC address of the unit (display only)
<LAN SETTINGS>
N02
AUTO NEGOTIATION
OFF,
ON
LAN connection auto-negotiation function on/off
setting
CONNECTION SPEED
10M,
100M
LAN connection speed setting
DUPLEX MODE
HALF,
FULL
Switch LAN connection between half and full
duplex mode
LINK CONDITION
UP, DOWN
LAN connection status (display only)
SET
ENTER to execute
Apply the auto-negotiation, connection speed,
and half/full duplex settings to the unit
<CNS SETTINGS>
N03
CNS MODE
LEGACY
, BRIGDE, MCS
Camera network system communications mode
setting
LEGACY: When connected with a command
network unit (such as the CNU-700) or remote
control unit (such as the RCP-3500/1500
series) via an 8-pin multi connector (excluding
when unit is connected to camera network
master device via LAN connection)
BRIDGE: When connected 1-to-1 with remote
control panel via LAN connection
MCS: When connected to camera network
master device, for example a master setup unit
(such as the MSU-1000), via LAN connection
MCS MODE
(CLIENT)
(Display only)
REMOTE CONTROL NO
Number setting of device used for remote
control (remote control is disabled when set to
0)
CH.A
0
to 96
CH.B
0
to 96
MASTER IP ADDRESS
0.0.0.0
to 255.255.255.255
IP address setting of the master device
(enabled in MCS mode only)
TARGET IP
ADDRESS(CH.A)
0.0.0.0
to 255.255.255.255
IP address setting of remote control panel in
bridge connection (enabled in BRIDGE mode
only)
TARGET IP
ADDRESS(CH.B)
0.0.0.0
to 255.255.255.255
SET
ENTER to execute
Apply the CNS mode, device number, master IP
address, and target IP address settings in the
menu to the unit
Page name
Page No.
Item
Set value
Meaning
<BOARD STATUS>
D01
SY
OK, NG
Internal board status
DVP
OK, NG
SDI
OK, NG
DCP1
OK, NG
DCP2
OK, NG