Sony MDSJE320 Service Manual - Page 19
Adjusting Points And Conneting Points, 8. Focus Bias Adjustment, 9. Error Rate Check, 10. Focus - mds je320
UPC - 027242541344
View all Sony MDSJE320 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 19 highlights
5-8. FOCUS BIAS ADJUSTMENT Adjusting Method : 1. Load a continuously recorded disc (Refer to "5-4. Creating Continuously Recorded Disc".). 2. Rotate the AMS knob and display "CPLAY MODE". 3. Press the YES button and display "CPLAY MID". 4. Press the EDIT/NO button when "C1 = AD = " is displayed. 5. Rotate the AMS knob and display "FBIAS ADJUST". 6. Press the YES button and display " / a = ". The first four digits indicate the C1 error rate, the two digits after [/] indicate ADER, and the 2 digits after [a =] indicate the focus bias value. 7. Rotate the AMS knob in the clockwise direction and find the focus bias value at which the C1 error rate becomes 220 (Refer to Note 2). 8. Press the YES button and display " / b = ". 9. Rotate the AMS knob in the counterclockwise direction and find the focus bias value at which the C1 error rate becomes 220. 10. Press the YES button and display " / c = ". 11. Check that the C1 error rate is below 50 and ADER is 00. Then press the YES button. 12. If the "( )" in " - - ( )" is above 20, press the YES button. If below 20, press the EDIT/NO button and repeat the adjustment from step 2. 13. Press the §EJECT button to remove the continuously recorded disc. Note 1 : The relation between the C1 error and focus bias is as shown in the following figure. Find points a and b in the following figure using the above adjustment. The focal point position C is automatically calculated from points a and b. Note 2 : As the C1 error rate changes, perform the adjustment using the average vale. C1 error 220 b c Focus bias value (F. BIAS) a 5-9. ERROR RATE CHECK 5-9-1. CD Error Rate Check Checking Method : 1. Load a check disc (MD) TDYS-1. 2. Rotate the AMS knob and display "CPLAY MODE". 3. Press the YES button twice and display "CPLAY MID". 4. The display changes to "C1 = AD = ". 5. Check that the C1 error rate is below 20. 6. Press the EDIT/NO button, stop playback, press the §EJECT button, and remove the test disc. 5-9-2. MO Error Rate Check Checking Method : 1. Load a continuously recorded disc (Refer to "5-4. Creating Continuously Recorded Disc".). 2. Rotate the AMS knob and display "CPLAY MODE". 3. Press the YES button and display "CPLAY MID". 4. The display changes to "C1 = AD = ". 5. If the C1 error rate is below 50, check that ADER is 00. 6. Press the EDIT/NO button, stop playback, press the §EJECT button, and remove the continuously recorded disc. 5-10. FOCUS BIAS CHECK Change the focus bias and check the focus tolerance amount. Checking Method : 1. Load a continuously recorded disc (Refer to "5-4. Creating Continuously Recorded Disc".). 2. Rotate the AMS knob and display "CPLAY MODE". 3. Press the YES button twice and display "CPLAY MID". 4. Press the EDIT/NO button when "C1 = AD = " is displayed. 5. Rotate the AMS knob and display "FBIAS CHECK". 6. Press the YES button and display " / c = ". The first four digits indicate the C1 error rate, the two digits after [/] indicate ADER, and the 2 digits after [c =] indicate the focus bias value. Check that the C1 error is below 50 and ADER is 00. 7. Press the YES button and display " / b = ". Check that the C1 error is not below 220 and ADER is not above 00 every time. 8. Press the YES button and display " / a = ". Check that the C1 error is not below 220 and ADER is not above 00 every time. 9. Press the EDIT/NO button, next press the §EJECT button, and remove the continuously recorded disc. Note 1 : If the C1 error and ADER are above 00 at points a (step 8. in the above) or b (step 7. in the above), the focus bias adjustment may not have been carried out properly. Adjust perform the beginning again. 5-11. ADJUSTING POINTS AND CONNETING POINTS [BD BOARD] (SIDE A) 1 5 CN110 NOTE RF I + 3V VC TEO IOP CN101 D101 IC192 NOTE : It is useful to use the jig. for checking the waveform. (Refer to Servicing Note on page 4.) MDS-JE320 - 19 - - 20 -