Sony STR-DN1080 Operating Instructions - Page 52

CONNECTING, Press one of the input buttons

Get Sony STR-DN1080 PDF manuals and user guides View all Sony STR-DN1080 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

4 Press / to select the name of the headphones/speakers, and then press . After "CONNECTING" flashes and the headphone name or speaker name is displayed, the BLUETOOTH connection is complete. CONNECTING Tip You can also switch the BLUETOOTH mode to TX (transmitter) mode by setting [Bluetooth Mode] to [Transmitter] in [Bluetooth Settings]. Then select the name of the headphones or speakers from [Device List] in [Bluetooth Settings]. If you cannot find your device name in the list, select [Scan]. XXXXXX * * "XXXXXX" represents the name of a detected BLUETOOTH device. 5 Press one of the input buttons to select the input you want. The sound is output from the BLUETOOTH headphones/speakers. No sound is output from the receiver. 6 Adjust the volume of the BLUETOOTH headphones/ speakers. Volume control on the receiver and remote control only works for the BLUETOOTH headphones/speakers. Note  The most recently connected BLUETOOTH device can be reconnected simply by performing step 1 above.  The one-touch connection (NFC) cannot be used in TX (transmitter) mode.  When "NOT. USE" appears on the display panel, you cannot switch BLUETOOTH mode. Check the following:  BLUETOOTH function is in use  [Bluetooth Mode] is set to [Off] 52GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
52
GB
4
Press
/
to select the name of
the headphones/speakers,
and then press
.
After “CONNECTING” flashes and the
headphone name or speaker name is
displayed, the BLUETOOTH connection is
complete.
*
“XXXXXX” represents the name of a detected
BLUETOOTH device.
5
Press one of the input buttons
to select the input you want.
The sound is output from the
BLUETOOTH headphones/speakers. No
sound is output from the receiver.
6
Adjust the volume of the
BLUETOOTH headphones/
speakers.
Volume control on the receiver and
remote control only works for the
BLUETOOTH headphones/speakers.
The most recently connected BLUETOOTH device
can be reconnected simply by performing step 1
above.
The one-touch connection (NFC) cannot be used in
TX (transmitter) mode.
When “NOT. USE” appears on the display panel,
you cannot switch BLUETOOTH mode. Check the
following:
BLUETOOTH function is in use
[Bluetooth Mode] is set to [Off]
You can also switch the BLUETOOTH mode to TX
(transmitter) mode by setting [Bluetooth Mode] to
[Transmitter] in [Bluetooth Settings]. Then select the
name of the headphones or speakers from [Device
List] in [Bluetooth Settings]. If you cannot find your
device name in the list, select [Scan].
Note
CONNECTING
XXXXXX
*
Tip