Sony STR-ZA2100ES Installation Guide - Page 18
List of messages after Auto Calibration measurements, Saving/loading settings of the receiver
View all Sony STR-ZA2100ES manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 18 highlights
5 Save the measurement results. Select [Save] in step 4. Calibration Matching When Auto Calibration is executed, this function works automatically to match the distance and level of the right and left speakers. You can set this function only after the D.C.A.C. measurement process has been completed and the results of D.C.A.C. measurement are saved. The setting is valid until you change it. Note • If an error code or warning message appears on the screen in step 3, see "List of messages after Auto Calibration measurements" (page 18). Tips • You can also perform automatic calibration by pressing the AUTO CAL button on the remote control. If you use the AUTO CAL button, the following restrictions apply to the operation: -- Prior settings relating to the Auto Calibration will be skipped. -- You can only use the display panel for the operation. • The Auto Calibration function will be canceled if you perform the following during the measurement process: -- Turn the receiver on or off. -- Press the input buttons on the remote control or on the receiver. -- Press . -- Press SPEAKERS on the receiver. -- Press HDMI OUTPUT. -- Press AMP MENU. -- Press HOME. -- Press AUTO CAL. -- Change the volume level. List of messages after Auto Calibration measurements • Code 31: Front speakers are not selected properly. Select the front speakers using SPEAKERS, and then perform Auto Calibration again. • Code 32, Code 33: -- Speakers were not detected or not connected properly. -- None of the front speakers are connected or only one front speaker is connected. -- Either the surround left or surround right speaker is not connected. -- A surround back speaker is connected only to the SPEAKERS SURROUND BACK/HEIGHT (FRONT B/BI-AMP/ZONE 2) R terminal. If connecting only one surround back speaker, connect it to the SPEAKERS SURROUND BACK/HEIGHT (FRONT B/BI-AMP/ZONE 2) L terminal. -- Either the Height1 left or Height1 right speaker is not connected (for STR-ZA3100ES/STR-ZA2100ES). -- Either the Height2 left or Height2 right speaker is not connected (for STR-ZA3100ES/STR-ZA2100ES). -- Either the Height left or Height right speaker is not connected (for STR-ZA1100ES). -- The calibration microphone is not connected. Make sure that the calibration microphone is connected properly, and then perform Auto Calibration again. If the calibration microphone is connected properly but the error code still appears, the calibration microphone cable may be damaged. • Code 34: Speakers are not placed in the proper position. Speakers or the calibration microphone on the right or left may be placed wrongly. See the supplied Startup Guide and check the speaker position. • Code 35: The measurement result is not match to the speaker pattern you set. See the Help Guide and change the setting to fit the actual speaker pattern. • Warning 40: The measurement process has been completed and a high noise level has been detected. You may be able to achieve better results if you try the process again in a quiet environment. • Warning 41, Warning 42: -- The input from the calibration microphone is too large. -- The distance between the speaker and the calibration microphone may be too small. Set them further apart and perform the measurement again. • Warning 43: The distance and position of a subwoofer cannot be detected. This may be caused by noise. Try performing the measurement in a quiet environment. • Warning 44: Measurement has been completed. However the speakers are not placed in the proper position with respect to each other. See the supplied Startup Guide and check the relative positions of the speakers. • NO WARNING: There is no warning information. Saving/loading settings of the receiver You can save the settings to a USB flash drive and restore the saved settings to the receiver or to another receiver of the same model. Saving Loading To save the settings Insert a USB flash drive to the USB port on the front panel of the receiver. Select [Setup] - [Install Setup] - [Save/Load] - [Save] from the home menu. To load the settings Insert to the USB port on the front panel of the receiver a USB flash drive on which the settings are saved. Select [Setup] - [Install Setup] - [Save/Load] - [Load] from the home menu. 18US