Stihl FS 80 Instruction Manual - Page 30

Mounting the Mowing Head, Removing the Mowing Head, Adjusting Nylon Line

Get Stihl FS 80 PDF manuals and user guides View all Stihl FS 80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

English / USA Removing the Mowing Head : Block the output shaft. STIHL SuperCut 20-2, STIHL AutoCut 25-2, STIHL AutoCut C 25-2, STIHL TrimCut 30-2, STIHL PolyCut 20-3 1 : Unscrew the mowing head clockwise. Mounting the Mowing Head Keep instruction sheet for mowing head in a safe place. : Screw the STIHL SuperCut 20-2, STIHL AutoCut 25-2, STIHL AutoCut C 25-2, STIHL TrimCut 30-2, STIHL PolyCut 20-3 counterclockwise onto the shaft (1) as far as stop. : Block the output shaft. : Tighten down the mowing head. Remove the tool used to block the shaft. 002BA081 KN STIHL FixCut 25-2 : Place the mowing head on the thrust plate (2). Collar (arrows) must locate in the mowing head's mounting hole : Push the thrust washer (3) over the shaft (1) so that it locates against the base. : Block the output shaft. : Screw the mounting nut (4) with the combination wrench (5) counterclockwise on to the output shaft and tighten down firmly. Remove the tool used to block the shaft. STIHL FixCut 25-2 : Use the combination wrench to unscrew the mounting nut clockwise from the output shaft If the mounting nut is too loose, fit a new one Adjusting Nylon Line STIHL SuperCut Fresh line is advanced automatically if remaining line is still min. 2 1/2" (6 cm) long. The blade on the deflector trims overlong line to the correct length. FS 80, FS 80 R, FS 85, FS 85 R 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
29
FS 80, FS 80 R, FS 85, FS 85 R
English / USA
Mounting the Mowing Head
Keep instruction sheet for mowing head
in a safe place.
:
Screw the
STIHL SuperCut 20-2,
STIHL AutoCut 25-2,
STIHL AutoCut C 25-2,
STIHL TrimCut 30-2,
STIHL PolyCut 20-3
counterclockwise onto the shaft (
1
)
as far as stop.
:
Block the output shaft.
:
Tighten down the mowing head.
Remove the tool used to block the
shaft.
STIHL FixCut 25-2
:
Place the mowing head on the
thrust plate (
2
).
Collar (
arrows
) must locate in the
mowing head’s mounting hole
:
Push the thrust washer (
3
) over the
shaft (
1
)
so that it locates against
the base.
:
Block the output shaft.
:
Screw the mounting nut (
4
)
with the
combination wrench
(
5
)
counterclockwise on to the output
shaft and tighten down firmly.
Remove the tool used to block the
shaft.
Removing the Mowing Head
:
Block the output shaft.
STIHL SuperCut 20-2,
STIHL AutoCut 25-2,
STIHL AutoCut C 25-2,
STIHL TrimCut 30-2,
STIHL PolyCut 20-3
:
Unscrew the mowing head
clockwise.
STIHL FixCut 25-2
:
Use the combination wrench to
unscrew the mounting nut clockwise
from the output shaft
If the mounting nut is too loose, fit a
new one
Adjusting Nylon Line
STIHL SuperCut
Fresh line is advanced automatically if
remaining line is still
min. 2 1/2" (6 cm
)
long. The blade on the deflector trims
overlong line to the correct length.
1
002BA081 KN