Stihl FS 88 Instruction Manual - Page 28

Scm/1.

Get Stihl FS 88 PDF manuals and user guides View all Stihl FS 88 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

c;- 2 1 3 "c 4 I~ Adjusting nylon line • Hold the rotating mowing head horizontal above the ground tap it on the ground about 3cm/1 1/4" fresh line is advanced - blade on deflector trims surplus line to the correct length avoid tapping head more than once. • Line feed operates only if both lines still have a minimum length of 2.Scm/1". • Fit new nylon line as described in instructions supplied with mowing head. STIHL Autocut 24-2 STIHL Polymatic 30-2 • Lay your brushcutter on its back with the gear head facing up. • Slip the plain washer (1) and thrust washer (2) over the shaft (3) and against the thrust plate (4). • Screw mowing head counterclockwise onto the output shaft as far as it will go. • Block the output shaft. • Tighten down the mowing head securely. Important! Remove the stop pin. Keep instruction sheet for mowing head in a safe place. Removing mowing head • Block the output shaft. • Uns.f.rew mowing head clockwise. Adjusting nylon line • Refer to instruction sheet supplied with mowing head. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
Adjusting nylon line
•
Hold the rotating mowing head
horizontal above the ground -
tap
it
on the ground -
about
3cm/1 1/4"
fresh line
is
advanced - blade on deflector trims
surplus line
to
the correct length -
avoid tapping head more than
once.
•
Line feed operates only if both lines
still have a
minimum length
of
2.Scm/1".
•
Fit new nylon line as described
in
instructions supplied with mowing
head.
c;-
2
1
3
4
"c
I~
STIHL Autocut 24-2
STIHL
Polymatic 30-2
•
Lay your brushcutter on its back
with the gear head facing up.
•
Slip the plain washer
(1)
and
thrust washer
(2)
over the
shaft
(3)
and against the
thrust plate (4).
•
Screw mowing head counterclock-
wise onto the output shaft -
as far as
it
will go.
•
Block the output shaft.
•
Tighten down the mowing head
securely.
Important!
Remove the stop pin.
Keep instruction sheet for mowing
head in a safe place.
Removing mowing head
•
Block the output shaft.
•
Uns.f.rew mowing head clockwise.
Adjusting nylon line
•
Refer to instruction sheet supplied
with mowing head.
27