Stihl HT 75 Instruction Manual - Page 17

Mounting the Bar and Chain, at the same time.

Get Stihl HT 75 PDF manuals and user guides View all Stihl HT 75 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

390BA044 KN english Mounting the Bar and Chain 51 43 390BA042 KN : Unscrew nut and take off cover. 1 2 : Turn tensioning screw (1) counterclockwise until the tensioning nut (2) butts against the left end of the housing slot, then back it off 5 full turns. 390BA043 KN The chain is very sharp - wear work gloves to protect hands from cuts. : Fit the chain - start at the bar nose. 390BA003 KN : Fit guide bar over the stud (3). Engage peg of tensioner slide in locating hole (4) - place the chain over sprocket (5) at the same time. : Now turn tensioning screw (1) clockwise until there is very little chain sag on the underside of the bar - and the drive link tangs are located in the bar groove. : Refit the sprocket cover and screw on the nut only fingertight. : Now refer to "Tensioning the Saw Chain". 16 HT 70, HT 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
16
english
HT 70, HT 75
:
Unscrew nut and take off cover.
:
Turn tensioning screw
(1)
counterclockwise until the
tensioning nut
(2)
butts against the
left end of the housing slot, then
back it off 5 full turns.
The chain is very sharp – wear work
gloves to protect hands from cuts.
:
Fit the chain –
start at the bar nose.
:
Fit guide bar over the stud
(3)
.
Engage peg of tensioner slide in
locating hole
(4)
– place the chain
over sprocket
(5)
at the same time.
:
Now turn tensioning screw
(1)
clockwise until there is very little
chain sag on the underside of the
bar – and the drive link tangs are
located in the bar groove.
:
Refit the sprocket cover and screw
on the nut only fingertight.
:
Now refer to "Tensioning the Saw
Chain".
Mounting the Bar and Chain
390BA042 KN
1
2
390BA043 KN
390BA003 KN
1
5
390BA044 KN
4
3