Stihl HT 75 Instruction Manual - Page 36

Storing the Machine, Checking the Chain Sprocket, Fitting the Starter Cover

Get Stihl HT 75 PDF manuals and user guides View all Stihl HT 75 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Storing the Machine Checking the Chain Sprocket english Fitting the Starter Cover : Push the upper mounting boss under the shroud - line up the tank and push the lower part of cover onto the tank. : Insert and tighten down the housing screws. Secure cable lug (arrow) in position (if fitted on your machine). 410BA019 KN 390BA012 KN For periods of about 3 months or longer: : Drain and clean the fuel tank in a well ventilated area. : Run engine until carburetor is dry, this helps prevent the carburetor diaphragms sticking together. : Remove the saw chain and guide bar, clean them and spray with corrosion inhibiting oil. : Thoroughly clean the machine, pay special attention to the cylinder fins and air filter. : If you use a biological chain and bar lubricant, e.g. STIHL BioPlus, completely fill the chain oil tank. : Store the machine in a dry and high or locked location, out of the reach of children and other unauthorized persons. a Replace the chain sprocket after using two chains! Replace sooner if the wear marks on the sprocket are deeper than about 0,02" (0.5 mm)(dimension a) since this would otherwise shorten the life of the chain. Use gauge - see "Special Accessories" - to check the depth of the wear marks. It is best to use two chains in rotation with one sprocket. Use only original STIHL chain sprockets! HT 70, HT 75 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
35
HT 70, HT 75
english
Fitting the Starter Cover
:
Push the upper mounting boss
under the shroud –
line up the tank and push the lower
part of cover onto the tank.
:
Insert and tighten down the housing
screws.
Secure cable lug (arrow) in position
(if fitted on your machine).
For periods of about 3 months or longer:
:
Drain and clean the fuel tank in a
well ventilated area.
:
Run engine until carburetor is dry,
this helps prevent the carburetor
diaphragms sticking together.
:
Remove the saw chain and guide
bar, clean them and spray with
corrosion inhibiting oil.
:
Thoroughly clean the machine,
pay special attention to the cylinder
fins and air filter.
:
If you use a biological chain and bar
lubricant, e.g. STIHL BioPlus,
completely fill the chain oil tank.
:
Store the machine in a dry and high
or locked location, out of the reach
of children and other unauthorized
persons.
Replace the chain sprocket after using
two chains!
Replace sooner if the wear marks
on the sprocket are deeper than
about 0,02" (0.5 mm)(dimension
a
)
since this would otherwise shorten
the life of the chain.
Use gauge – see "Special
Accessories" – to check the depth of the
wear marks.
It is best to use two chains in
rotation with one sprocket.
Use only original STIHL chain sprockets!
410BA019 KN
Storing the Machine
Checking the Chain
Sprocket
a
390BA012 KN