Stihl TS 500i STIHL Cutquik Instruction Manual - Page 27

Tensioning the V-belt.

Get Stihl TS 500i STIHL Cutquik PDF manuals and user guides View all Stihl TS 500i STIHL Cutquik manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

N Insert the square nut into the guide in the guard and hold it in place N Screw in the shorter banjo bolt (6) and washer at the adjusting lever and tighten up with the combination wrench Mounting "cast arm with guard" - guard on the outboard side 2 2 2 56 6 6 N Fit the "starter cover with rewind starter" (5) over the studs (2) N Tighten up the nuts (6) by hand 1307BA008 KN English N Fit the support with the longer banjo bolt on the adjusting lever (3) - screw in the banjo bolt and tighten with the combination wrench N Insert the water hose into the guide in the V-belt guard (arrow) from the water connection towards the guard - avoid tight radiuses Checking the adjustment range of the guard 1307BA010 KN 12 12 12 7 8 1307BA009 KN 43 N Press the oblong holes (1) in the "cast arm and guard" on to the studs (2), guiding the ribbed V-belt over the front pulley NOTICE The belt action must run smoothly. N The belt tensioner (3) must sit close to the lug (4) 1307BA007 KN N Push the V-belt guard (7) into place N Screw in the bolt (8) and tighten up Connecting the water connection 3 1 2 1 N Insert the longer banjo bolt (1) through the connector (2) of the water attachment - observe the position of the connector N Insert the square nut into the guide in the guard and hold it in place 370BA078 KN A N Rotate the guard forwards and backwards as far as possible - adjustment range (A) must be limited by the stop pin Continue as described in the chapter "Tensioning the V-belt". TS 480i, TS 500i 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
TS 480i, TS 500i
English
25
N
Insert the square nut into the guide
in the guard and hold it in place
N
Screw in the shorter banjo bolt (6)
and washer at the adjusting lever
and tighten up with the combination
wrench
Mounting "cast arm with guard" – guard
on the outboard side
N
Press the oblong holes (1) in the
"cast arm and guard" on to the
studs (2), guiding the ribbed V-belt
over the front pulley
NOTICE
The belt action must run smoothly.
N
The belt tensioner
(3) must sit close
to the lug (4)
N
Fit the "starter cover with rewind
starter" (5) over the studs (2)
N
Tighten up the nuts (6) by hand
N
Push the V-belt guard (7) into place
N
Screw in the bolt (8) and tighten up
Connecting the water connection
N
Insert the longer banjo bolt (1)
through the connector (2) of the
water attachment – observe the
position of the connector
N
Insert the square nut into the guide
in the guard and hold it in place
N
Fit the support with the longer banjo
bolt on the adjusting lever (3) –
screw in the banjo bolt and tighten
with the combination wrench
N
Insert the water hose into the guide
in the V-belt guard (arrow) from the
water connection towards the guard
– avoid tight radiuses
Checking the adjustment range of the
guard
N
Rotate the guard forwards and
backwards as far as possible –
adjustment range (A) must be
limited by the stop pin
Continue as described in the chapter
“Tensioning the V-belt”.
2
2
3
4
1
2
1
1
1307BA007 KN
2
6
6
2
1307BA008 KN
2
5
6
7
8
1307BA009 KN
1
1
370BA078 KN
2
3
A
1307BA010 KN