Symphonic CSTL20D6 Owner's Manual - Page 11
Watching A Tv Program, Initial Set Up
View all Symphonic CSTL20D6 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 11 highlights
TV SECTION TV OPERATION AND SETTINGS TV OPERATION AND SETTINGS TV SECTION INITIAL SET UP WATCHING A TV PROGRAM TV When you turn on the power for the first time, the SELECT LANGUAGE screen is displayed. Select the language for screen display and perform auto programming of the channels. 1 After antenna or cable connection is completed, connect the power cord into a standard AC outlet. NOTE •If any digits are displayed in the corner of the screen, press [POWER] without unplugging the power cord. 1 Press[POWER] to turn on the unit. POWER NOTE • If the TV screen shows snow noise and there is no operation for more than 5 seconds, "HELPFUL HINTS" appears. - HELPFUL HINTS 1. PLEASE CHECK TO SEE IF THE ANTENNA/CABLE/SATELLITE IS PROPERLY CONNECTED. 2. DID YOU PERFORM "AUTO PRESET CH" ? 3. PLEASE REFER TO FRONT PAGE OF THE OWNER'S MANUAL OR REAR PANEL FOR SUPPORT LINE INFORMATION. Follow the instructions listed on-screen. • If those settings do not work properly, please call our help line on the front page of this owner's manual. 2 Press [CH. K / L] or the Number buttons to 2 Press [POWER] to turn on the unit. POWER 3 Press one of the keys listed below to select the desired language of on-screen menu. • ENGLISH: [CH. K] • ESPAÑOL: [CH. L] • FRANÇAIS: [VOL. X] SELECT LANGUAGE ENGLISH NEXT:PRESS CHK ESPAÑOL DESPUÉS:PRESIONE CHL FRANÇAIS APRÈS:PRESSEZ VOLX 4 Confirm the antenna (or cable) - INITIAL SETUP - connection and press [CH. K]. PLEASE CONNECT ANTENNA OR CABLE OR SATELLITE TO THIS UNIT. • The tuner scans and memorizes THEN PRESS CH K, IN ORDER TO PERFORM "AUTO PRESET CH ". all active channels in your area. 5 When the scanning is completed, the tuner stops on the lowest memorized CH 15 channel. (Example) NOTE •If [MENU] is pressed during channel scanning, the tuner stops scanning and the lowest memo- rized channel is displayed. •The INITIAL SETUP menu is displayed every time you turn on the unit unless the scanning is completed. •In case no channel can be received by the channel scan- ning, "NO TV SIGNALS" is NO TV SIGNALS displayed on the screen. Turn off the unit and check the antenna connection, then follow steps 1 to 5 again. •You can change the setting after completing INITIAL SET UP by LANGUAGE menu or CHANNEL SET UP menu. (Refer to "MENU LANGUAGE" on page 16 or "CHANNEL SET UP" on page 12.) select the desired channel number. CH. OR 123 456 789 +100 0 +10 NOTE For channel number selection with number buttons: • To select single-digit channel number, press [0] first. (e.g. Press [0] [2] for channel 2.) • To select cable channels which are higher than 99, press [+100/+10] first. (e.g. Press [+100/+10] [2] [5] for channel 125.) 3 Press [VOL. X / Y] to select the desired vol- ume level. VOL. VOLUME 20 C C C C CC CCCCCCCCCC • Press [MUTE] to instantly mute the sound. Press it again to restore the previous volume level. NOTE • If you press [CH. K / L] in the DVD mode, you can change the TV channels. Even if you turn off the unit in the DVD mode, when you turn it on again, it will go into the TV mode. TO WATCH CABLE OR SATELLITE CHANNEL If the unit is connected to a cable box or satellite box, press [CH. K / L] to select CH3 or CH4 according to the output channel setting of the device and select desired channel on that device. TO WATCH EXTERNAL INPUT When an external equipment is connected to AUDIO/VIDEO input jacks on the right side, press [SELECT] or [CH. K / L] repeatedly until "VIDEO1" or "VIDEO2" appears on the screen. - 11 - EN