Home » TASCAM Manuals » Audio Mixers » TASCAM DP-006 » Manual Viewer

TASCAM DP-006 Owners Manual - Page 94

– Message Lists

Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

14 - Message Lists The following popup messages alert you to conditions that may arise while you are using the unit. Consult this table if you see something you do not understand. Messages Battery Empty Battery Low Card Full Empty Export Track File Not Found Meaning and remedy The batteries have no remaining charge. This appears when the batteries have no remaining charge. Replace the batteries with new ones or use a TASCAM PS-P520 AC adapter (sold separately). The batteries have little remaining charge. This appears if you try to start recording when the batteries are low. Replace the batteries with new ones or use a TASCAM PS-P520 AC adapter (sold separately). The SD card is full during recording. Export or delete unneeded data to make room on the card or use a different SD card. There is no recorded data for the export track. This appears if you tried to export a track from the song that does not have any recordings. (See "Track import and export" on page 88.) Export tracks from songs with recordings. The file cannot be found. This appears if you try to restore a song when the FAT Partition does not have any backed up songs. (See "Song backup and restoration" on page 86.) I/O Too Short The IN and OUT points are too close together. This appears if you try to activate repeat playback mode when the IN and OUT points are too close together. Make sure the IN and OUT points are at least 2 frames apart. (See "Using repeat playback" on page 66.) Import File Not Found Import File Too Large In Bounce Mode In Master Mode The file you are trying to import cannot be found. You are trying to import a WAV file from the FAT partition when there are no WAV files there. (See "Importing to tracks" on page 88.) Connect the unit to a PC and transfer some files to the FAT partition for import. The file you are trying to import is too large. You are trying to import a WAV file from the MTR partition that is too large for the remaining space on the partition. Free up some space on the (native) partion and try again. The unit is in BOUNCEmode. You tried to perform an action that cannot be done while in BOUNCEmode. The unit is in MASTER RECor MASTER PLAYmode. You tried to perform an action that cannot be done while in MASTER RECor MASTER PLAYmode. 94 TASCAM DP-006

Section	Page
1 – Introduction	9
Features	9
Included items	9
Conventions used in this manual	10
Trademarks	10
About SD cards	11
Precautions for use	11
Precautions for installation	11
Beware of condensation	11
Cleaning the unit	11
2–Quick Start Guides	12
Playback and mixing	12
Preparing	12
Playing and mixing the demo song	13
Recording and mastering	15
Creating a new song	15
Setting the internal mics as input sources	16
Setting the internal mics as the recording sources for TRACK 3	17
Adjusting the input level and monitoring	18
Using internal mics to record rhythm guitar to TRACK 3	19
Listening to the recording	20
Connecting an electric guitar	20
Setting the guitar as an input source	21
Recording lead guitar to TRACK 2	21
Recording vocals on TRACK 1	23
Creating a stereo master track	25
Checking the stereo master track	27
Transferring the stereo master track to a computer	28
Shutting down	28
3 – Names and functions of parts	29
Top Panel	29
Front panel	31
Rear panel	32
Left side panel	32
Right side panel	33
Bottom panel	33
Home Screen	34
Menu structure	36
Screen operations	37
4 – Preparations	39
Preparing the power and SD card	39
Inserting an SD card	39
Removing an SD card	39
SD card write-protection switches	39
Preparing the power	40
Start-up & shutdown	41
Starting up the unit	41
Shutting down	41
Preparing SD cards for use	42
Recorder modes	42
Connecting with other equipment	43
Rear panel connections	43
Left side panel connections	43
Right side panel connections	44
Adjusting the contrast	44
5 – Song Management	45
Partitions and songs	45
Selecting the active partition	45
Editing names	46
Loading a saved song	46
Creating a new song	47
Saving a song	47
Viewing song information	48
Copying songs	48
Erasing songs	49
Protecting songs	50
6 – Basic Recording	51
Selecting the input source	51
Monitoring the input signal	52
Setting the monitoring mode	52
OL indicators and level meters	53
Assigning inputs	54
Setting the track type (Tracks 3 and 4 only)	54
Assigning inputs to stereo tracks (Tracks 3 and 4 only)	55
Assigning inputs to mono tracks	56
Making the first recording	56
Multitrack recording	57
Setting the recording tracks	57
Setting TRACK PAN/BAL and LEVEL values	57
Input selection and assignment	57
Setting input levels	58
Recording additional tracks	58
Undoing operations (undo)	58
Undoing the last operation (single undo)	58
Undoing a previous operation (multi-undo)	59
Erasing the operation history	60
7 – Recorder Functions	61
Punching in and out	61
Bouncing tracks	61
Using the bounce function	62
Confirming the result	63
Locate and search functions	64
Direct locate function	64
Returning to the song beginning (RTZ function) or the point where recording was last started (LRP function)	64
Search backward/forward	64
Repeat playback	65
Setting IN and OUT points	65
Using repeat playback	66
Setting the time between repetitions (repeat interval)	66
8 – Editing Tracks	67
Overview of track editing	67
Editing points	67
Basic editing procedures	67
Track editing function setting items	68
CLONE TRACK (track duplication)	69
CLEAN OUT (track erase)	70
SILENCE (part erase)	70
CUT (remove part)	71
OPEN (insert silence)	71
9 – Mixdown and mastering	72
Mixdown	72
Level and balance	72
Stereo position (panning)	72
Creating stereo master tracks	72
Setting the starting and ending points	72
Creating a stereo master track	72
Checking stereo master tracks	74
10 – Miscellaneous Functions	75
Metronome	75
Tuner	76
Automatic power saving function	77
Restoring preferences to default values	77
Viewing information	78
11 – SD Card Management	79
Overview of partitions	79
Formatting SD cards	79
Reformatting MTR partitions	81
Reformatting FAT partitions	82
Initializing SD cards	82
12 – Exchanging Data with a Computer	83
Supported operating systems	83
Connecting with a computer	84
Disconnecting	85
Song backup and restoration	86
Backing-up songs	86
Restoring songs	87
Track import and export	88
Importing to tracks	88
Exporting tracks	90
Exporting stereo master tracks	92
13 – Troubleshooting	93
14 – Message Lists	94
15 – Specifications	98
Media and file systems	98
Inputs and outputs	98
Analog audio input and output	98
Data input and output	98
Audio performance	98
Operating requirements	99
General	99
Backup memory	100
Dimensions	100
Block diagram	101

Match case Limit results 1 per page

TASCAM

DP-006

14 – Message Lists

The following popup messages alert you to conditions that may arise while you are using the unit. Consult this table if you see something you do not understand.

Messages

Meaning and remedy

Battery Empty

The batteries have no remaining charge.

This appears when the batteries have no remaining charge.

Replace the batteries with new ones or use a TASCAM PS-P520 AC adapter (sold separately).

Battery Low

The batteries have little remaining charge.

This appears if you try to start recording when the batteries are low.

Replace the batteries with new ones or use a TASCAM PS-P520 AC adapter (sold separately).

Card Full

The SD card is full during recording.

Export or delete unneeded data to make room on the card or use a different SD card.

Empty Export Track

There is no recorded data for the export track.

This appears if you tried to export a track from the song that does not have any recordings. (See “Track import and export” on page 88.)

Export tracks from songs with recordings.

File Not Found

The file cannot be found.

This appears if you try to restore a song when the FAT Partition does not have any backed up songs. (See “Song backup and restoration”

on page 86.)

I/O Too Short

The IN and OUT points are too close together.

This appears if you try to activate repeat playback mode when the IN and OUT points are too close together. Make sure the IN and OUT

points are at least 2 frames apart. (See “Using repeat playback” on page 66.)

Import File Not Found

The file you are trying to import cannot be found.

You are trying to import a WAV file from the FAT partition when there are no WAV files there. (See “Importing to tracks” on page 88.)

Connect the unit to a PC and transfer some files to the FAT partition for import.

Import File Too Large

The file you are trying to import is too large.

You are trying to import a WAV file from the MTR partition that is too large for the remaining space on the partition. Free up some space

on the (native) partion and try again.

In Bounce Mode

The unit is in

BOUNCE

mode.

You tried to perform an action that cannot be done while in

BOUNCE

mode.

In Master Mode

The unit is in

MASTER REC

MASTER PLAY

mode.

You tried to perform an action that cannot be done while in

MASTER REC

MASTER PLAY

mode.