Toshiba 32DT1U User Manual - Page 46

Setting the sleep timer, Displaying TV status information, Understanding the auto power off, feature

Get Toshiba 32DT1U PDF manuals and user guides View all Toshiba 32DT1U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Chapter 6: Using the TV's features Setting the sleep timer You can set the sleep timer to turn off the TV after a set length of time (maximum of 180 minutes). To set the sleep timer using the remote control: Press on the remote control to set the length of time until the TV turns off. Repeatedly press to increase the time in 10-minute increments, or press  or  to increase or decrease the time in 10-minute increments, to a maximum of 180 minutes. To set the sleep timer using the on-screen menus: 1無 Press and open the Setup menu. 2無 Highlight Sleep Timer and press . 3無 Press the Number buttons to enter the length of time in 10-minute increments. 4無 Highlight Done and press . Note: When a power failure occurs, the sleep timer setting may be cleared. To display the remaining sleep time: Press . Note: A message will display on-screen when there is one minute remaining on the sleep timer. To cancel the sleep timer: Repeatedly press until it is set to 0 minute. Displaying TV status information To display TV status information using RECALL: Press on the remote control. The following information will display (if applicable): • Current input (ANT/CABLE, VIDEO, etc.) • If ANT/CABLE is the current input, either "CABLE" (for cable TV) or "ANT" (for over-the-air broadcasts). • Channel number (if in ANT/CABLE mode) • Channel label (if set) • Digital signal strength indicator (bar graph in lower right corner of box; for ATSC signal only) • Stereo, Mono or SAP audio status (when HDMI input mode, Dolby Digital or PCM) 46 • Video resolution • Aspect ratio of incoming video signal (4:3 or 16:9) • V-Chip rating status • GameTimer (if set) To close the RECALL screen: Press again. To display TV status information using INFO: Press on the remote control. The following additional information will display for off air digital channels (if applicable): • Title • Duration • Detailed description Note: The location of the banner can be moved to the top or bottom of the screen by pressing  or  while the RECALL or INFO display is onscreen. Understanding the auto power off feature The TV will automatically turn itself off after approximately 15 minutes if it is tuned to a vacant channel or a station that completes its broadcast for the day. This feature functions in ANT/CABLE mode only. Understanding the last mode memory feature If the power is cut off while you are viewing the TV, the Last Mode Memory feature automatically turns on the TV when the power is resupplied. Note: If it's possible, and you will be away from the TV for an extended period of time you should unplug the power cord.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
Chapter 6: Using the TV’s features
46
Setting the sleep timer
You can set the sleep timer to turn off the TV after a
set length of time (maximum of 180 minutes).
To set the sleep timer using the remote control:
Press
on the remote control to set the length of
time until the TV turns off. Repeatedly press
to
increase the time in 10-minute increments, or press
p
or
q
to increase or decrease the time in 10-minute
increments, to a maximum of 180 minutes.
To set the sleep timer using the on-screen
menus:
1無
Press
and open the
Setup
menu.
2無
Highlight
Sleep Timer
and press
.
3無
Press the Number buttons to enter the length of
time in 10-minute increments.
4無
Highlight
Done
and press
.
Note:
When a power failure occurs, the
sleep timer setting may be cleared.
To display the remaining sleep time:
Press
.
Note:
A message will display on-screen when
there is one minute remaining on the sleep timer.
To cancel the sleep timer:
Repeatedly press
until it is set to 0 minute.
Displaying TV status information
To display TV status information using
RECALL:
Press
on the remote control.
The following information will display (if applicable):
•
Current input (
ANT/CABLE
,
VIDEO
, etc.)
•
If ANT/CABLE is the current input, either “CABLE”
(for cable TV) or “ANT” (for over-the-air broadcasts).
•
Channel number (if in
ANT/CABLE
mode)
•
Channel label (if set)
•
Digital signal strength indicator (bar graph in lower
right corner of box; for ATSC signal only)
•
Stereo, Mono or SAP audio status (when HDMI input
mode, Dolby Digital or PCM)
•
Video resolution
•
Aspect ratio of incoming video signal (4:3 or 16:9)
•
V-Chip rating status
•
GameTimer (if set)
To close the RECALL screen:
Press
again.
To display TV status information using INFO:
Press
on the remote control.
The following additional information will display for
off air digital channels (if applicable):
•
Title
•
Duration
•
Detailed description
Note:
The location of the banner can be moved
to the top or bottom of the screen by pressing
p
or
q
while the RECALL or INFO display is on-
screen.
Understanding the auto power off
feature
The TV will automatically turn itself off after
approximately 15 minutes if it is tuned to a vacant
channel or a station that completes its broadcast for the
day. This feature functions in
ANT/CABLE
mode only.
Understanding the last mode
memory feature
If the power is cut off while you are viewing the
TV, the Last Mode Memory feature automatically
turns on the TV when the power is resupplied.
Note:
If it’s possible, and you will be away
from the TV for an extended period of time you
should unplug the power cord.