Weider Pro 9600 English Manual - Page 7

Attach the Press Seat Frame 7 to the Press Front

Get Weider Pro 9600 PDF manuals and user guides View all Weider Pro 9600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

5. Attach the Butterfly Seat Frame (14) to the Butterfly Upright (1) with two 3/8" x 3 1/4" Bolts (62), two 3/8" Flat Washers (48), and two 3/8" Nylon Locknuts (50). Attach the Butterfly Seat Frame (14) to the Butterfly Front Leg (3) with two 3/8" x 3 1/4" Bolts (62), two 3/8" Flat Washers (48) and two 3/8" Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet. 6. Press a 2 1/2" Square Inner Cap (76) into the Press Front Leg (20). Attach the Press Front Leg (20) to the indicated 3/8" x 2" Carriage Bolts (92) on the Press Base (6) with two 3/8" Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet. Make sure that the Press Front Leg is turned so that the indicated hole is on the side shown. 5 62 1 48 6 76 Hole 20 50 50 50 50 14 50 3 48 62 50 6 92 7. Attach the Press Seat Frame (7) to the Press Upright (2) with two 3/8" x 3 1/4" Bolts (62), two 3/8" Flat Washers (48), and two 3/8" Nylon Locknuts (50). Attach the Press Seat Frame (7) to the Press Front Leg (20) with two 3/8" x 3 1/4" Bolts (62), two 3/8" Flat Washers (48), and two 3/8" Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet. 8. Insert three 1 1/2" x 2 1/2" Inner Caps (83) into the ends of the Butterfly Top Frame (33). Attach the Butterfly Top Frame (33) to the Butterfly Upright (1) with two 3/8" x 2 1/2" Bolts (87), a Support Plate (94), and two 3/8" Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet. 7 50 7 50 48 62 48 50 20 50 2 48 62 48 8 33 83 87 83 94 83 50 1 50 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
5.
Attach the Butterfly Seat Frame (14) to the Butterfly
Upright (1) with two 3/8” x 3 1/4” Bolts (62), two 3/8”
Flat Washers (48), and two 3/8” Nylon Locknuts
(50).
Attach the Butterfly Seat Frame (14) to the Butterfly
Front Leg (3) with two 3/8” x 3 1/4” Bolts (62), two
3/8” Flat Washers (48) and two 3/8” Nylon Locknuts
(50).
Do not tighten the Nylon Locknuts yet.
6.
Press a 2 1/2” Square Inner Cap (76) into the Press
Front Leg (20).
Attach the Press Front Leg (20) to the indicated
3/8” x 2” Carriage Bolts (92) on the Press Base (6)
with two 3/8” Nylon Locknuts (50).
Do not tighten
the Nylon Locknuts yet. Make sure that the
Press Front Leg is turned so that the indicated
hole is on the side shown.
7.
Attach the Press Seat Frame (7) to the Press
Upright (2) with two 3/8” x 3 1/4” Bolts (62), two 3/8”
Flat Washers (48), and two 3/8” Nylon Locknuts
(50).
Attach the Press Seat Frame (7) to the Press Front
Leg (20) with two 3/8” x 3 1/4” Bolts (62), two 3/8”
Flat Washers (48), and two 3/8” Nylon Locknuts
(50).
Do not tighten the Nylon Locknuts yet.
6
7
76
50
50
6
20
Hole
5
3
1
62
50
62
50
14
50
48
50
48
7
50
20
7
2
48
48
48
48
62
50
50
62
50
8
83
87
94
33
83
50
1
50
8.
Insert three 1 1/2” x 2 1/2” Inner Caps (83) into the
ends of the Butterfly Top Frame (33).
Attach the Butterfly Top Frame (33) to the Butterfly
Upright (1) with two 3/8” x 2 1/2” Bolts (87), a
Support Plate (94), and two 3/8” Nylon Locknuts
(50).
Do not tighten the Nylon Locknuts yet.
83
92