Xerox 850DX Xerox Wide Format 8825/8830/8850/8855/X2 Tech System Introduction - Page 54

& X2-TECH Controller Status LEDs

Get Xerox 850DX - Phaser Color Solid Ink Printer PDF manuals and user guides
UPC - 042215454865
View all Xerox 850DX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

XES Synergix 8825/8830/8850/8855 & X2-TECH System Introduction 46 8855 & X2-TECH Controller Status LEDs AccXES Controllers (UP8 for 8855 and KLF for X2-TECH include 4 status LEDs used to indicate the following conditions: Controller Status LEDs LED Number Color LED 1 Green LED 2 Green LED 3 Yellow LED 4 Red Indicated Condition "Ready." Indicates that Controller is powered up and ready to process incoming jobs. "Busy." Indicates that Controller is busy processing a job. "Mismatch." Indicates that a media mismatch has occurred, which may be blocking the print queue. Also displayed when the Controller's Accounting Disk is full, or when the Controller has reached its Accounting record limit. Check the Web PMT's Main Page to determine the problem. "Attention." Indicates that a Printer or Finisher fault has occurred. May indicate a paper jam, out of toner condition, out of media condition, or a communications problem with one of the devices. During power-on self test (POST), the firmware will light LEDs 2, 3, and 4. After POST has successfully completed, LEDs 2, 3, and 4 will be switched OFF, and LED 1 will be switched ON. If POST did not successfully complete, all 4 LEDs will be switched OFF (i.e. they will be unlit).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
XES Synergix 8825/8830/8850/8855 & X2-TECH System Introduction
46
8855 & X2-TECH Controller
Status LEDs
AccXES Controllers (UP8 for 8855 and KLF for X2-TECH include 4 status
LEDs used to indicate the following conditions:
Controller Status LEDs
LED Number
Color
Indicated Condition
LED 1
Green
"Ready."
Indicates that Controller is powered
up and ready to process incoming jobs.
LED 2
Green
"Busy."
Indicates that Controller is busy
processing a job.
LED 3
Yellow
"Mismatch."
Indicates that a media mismatch
has occurred, which may be blocking the print
queue.
Also displayed when the Controller's
Accounting Disk is full, or when the Controller
has reached its Accounting record limit.
Check the Web PMT's Main Page to
determine the problem.
LED 4
Red
"Attention."
Indicates that a Printer or Finisher
fault has occurred.
May indicate a paper jam,
out of toner condition, out of media condition,
or a communications problem with one of the
devices.
During power-on self test (POST), the firmware will light LEDs 2, 3, and 4.
After POST has successfully completed, LEDs 2, 3, and 4 will be switched
OFF, and LED 1 will be switched ON.
If POST did not successfully complete,
all 4 LEDs will be switched OFF (i.e. they will be unlit).