Yamaha CLP-950 Owner's Manual - Page 50
Montieren Sie die Tastatureinheit A.
View all Yamaha CLP-950 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 50 highlights
3 10 cm 10 cm G The bracket on the front has 2 holes. Insert the screws into the holes on the front panel side of the bracket. G Die vorderen Winkelbleche haben zwei Schraubenbohrungen. Führen Sie die Schraube jeweils in die Bohrung an der Stirnwandseite ein. G La partie avant de la ferrure comporte deux trous. Introduisez les vis de fixation dans les trois du côté du panneau avant de la ferrure. GLa ménsula de la parte frontal tiene 2 orificios. Inserte los tornillos en los orificios del lado del panel frontal de la ménsula. A G Be sure to place your hands at least 10 centimeters from either end of the main unit when positioning it. G Mindestens 10 cm innen unter die Tastatureinheit greifen. G Placez bien vos mains à 10 cm au moins des extrémités du clavier, lors de sa mise en place. G Asegúrese de colocar las manos por lo menos a 10 centímetros desde los extremos de la unidad principal cuando la sitúe. C Install the main unit (A). Place the main unit (A) on the side panels (B) with the screws on its bottom panel (toward the rear of the main unit) just behind the grooves in the brackets located at the top of the side panels. Then slide the main unit forward until it stops. WATCH YOUR FINGERS WHEN DOING THIS!! Align the holes on the bottom panel of the main unit with the holes in the brackets on the side panels (also center the main unit to produce equal clearance on the left and right sides, as shown in the illustration), then use the four 6 x 16 millimeter flat-head screws 3 to attach the main unit. The four screws can be attached from the rear. CAUTION • Do not hold the keyboard in any position other than the position shown in the above illustration. • Fingers can become pinched between the main unit and the rear or side panels, be extra careful so as not to drop the main unit. V Connect the speaker cord. The speaker cord from the speaker box must be plugged into the corresponding connector in the main unit. The plug only goes in one way (the lug on the connector should face the rear of the main unit, as shown in the illustration), so don't try to force it in the wrong way around. B Connect the pedal cord. The pedal cord from the pedal box must be plugged into the PEDAL connector located at the rear of the main unit's underside. Once connected, attach the cord holders to the side panel as shown, then clip the cord into the holders. 6 x 16 mm flat-head screws 3 6 x 16 mm Senkschrauben 3 Vis à tête plate de 6 x 16 mm 3 Tornillos de cabeza plana de 6 x 16 mm 3 C Montieren Sie die Tastatureinheit (A). Setzen Sie die Tastatureinheit (A) so auf den fertigen Ständer, daß die beiden Schrauben an ihrer Unterseite hinter den Winkelblechen mit Führungsschlitz an der Hinterseite des Ständers zu liegen kommen. Schieben Sie die Tastatureinheit dann bis zum Anschlag in die Schlitze. KLEMMEN SIE IHRE FINGER DABEI NICHT EIN!! Richten Sie die Schraubenbohrungen an der Unterseite der Tastatureinheit mit den Bohrungen der Winkelbleche aus (achten Sie auch darauf, daß sie mittig auf dem Ständer steht, wie in der Abbildung gezeigt), um die Tastatureinheit dann mit den vier 6 x 16 mm Senkschrauben 3 festzuschrauben. Die vier Schrauben können von der Rückseite her eingeführt werden. VORSICHT • Halten Sie die Tastatureinheit nur wie in der obigen Abbildung! • Achten Sie darauf, daß Sie Ihre Finger nicht zwischen Tastatur- einheit und den Seitenwänden bzw. der Rückwand einklemmen - die Tastatureinheit könnte dadurch zu Fall kommen! V Schließen Sie das Lautsprecherkabel an. Das vom Lautsprecher kommende Kabel wird an die entsprechende Buchse an der Tastatrureinheit angeschlossen. Der Kabelstecker paßt nur in einer Ausrichtung in die Buchse (mit der Führungsnase zur Rückseite des Instruments weisend, wie in der Abbildung verdeutlicht). Versuchen Sie nicht, den Stecker falsch herum mit Gewalt in die Buchse zu drücken! B Schließen Sie das Pedalkabel an. Das vom Pedalkasten kommende Pedalkabel wird an die PEDAL-Buchse hinten an der Unterseite der Tastatureinheit angeschlossen. Bringen Sie nach dem Anschluß die Kabelhalter an der Seitenwand an, um das Kabel dann in diese Halter zu klemmen. 50 CLP-950/930