Yamaha DVX-S302 Owner's Manual - Page 25

Connecting the FM/AM antennas, TV IN, AV MONITOR OUT

Page 25 highlights

OTHER CONNECTIONS TV IN terminal To listen to TV channels through this DVD receiver, use the audio cables (white/red, not supplied) to connect the TV IN jacks to the corresponding audio out jacks on your TV. Notes - When using AV MONITOR OUT terminal to listen to the TV channels, set the DVD receiver's component setting to "RGB" (see page 25). - When using TV IN terminal, set the DVD receiver's component setting to"YUV" (see page 25). ■ Connecting the FM/AM antennas AM loop antenna 1 FM wire antenna 2 FM ANT GND AM ANT TO SUBWOOFER IN SYSTEM CONNECTOR Ground (GND terminal) For minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth. 1 Connect the supplied AM loop antenna to the AM ANT terminal. Place the AM loop antenna on a shelf or attach it to a stand or wall. 2 Connect the supplied FM wire antenna to the FM ANT terminal. Extend the FM wire antenna and fix its ends to the wall. For better FM stereo reception, connect an external FM antenna (not supplied). Notes - Adjust the position of the antennas for optimal reception. - Position the antennas as far as possible from your TV, VCR or other sources of radiation to prevent unwanted interference. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65

OTHER CONNECTIONS
20
TV IN terminal <E>
To listen to TV channels through this DVD receiver, use
the audio cables (white/red, not supplied) to connect the
TV IN
jacks to the corresponding audio out jacks on your
TV.
When using
AV MONITOR OUT
terminal to
listen to the TV channels, set the DVD receiver’s
component setting to “
RGB
” (see page 25).
When using
TV IN
terminal, set the DVD
receiver’s component setting to“
YUV
” (see
page 25).
Connecting the FM/AM antennas
1
Connect the supplied AM loop antenna to the
AM
ANT
terminal. Place the AM loop antenna on a shelf
or attach it to a stand or wall.
2
Connect the supplied FM wire antenna to the
FM
ANT
terminal. Extend the FM wire antenna and fix its
ends to the wall.
For better FM stereo reception, connect an external
FM antenna (not supplied).
Adjust the position of the antennas for optimal
reception.
Position the antennas as far as possible from your
TV, VCR or other sources of radiation to prevent
unwanted interference.
Notes
Notes
SYSTEM
CONNECTOR
IN
FM
ANT
AM
ANT
GND
TO SUBWOOFER
1
2
Ground (GND terminal)
For minimum interference, connect
the antenna GND terminal to a good
earth ground. A good earth ground
is a metal stake driven into moist
earth.
FM wire
antenna
AM loop
antenna