Yamaha HTR-5460 Owner's Manual - Page 30

Notes on playing a source, encoded with a DTS signal, indicator may flash immediately after

Get Yamaha HTR-5460 PDF manuals and user guides View all Yamaha HTR-5460 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

BASIC PLAYBACK s Notes on playing a source encoded with a DTS signal • If the digital output data of the player has been processed in any way, you may not be able to perform DTS decoding even if you make a digital connection between this unit and the player. • If you play a source encoded with a DTS signal and set the input mode to ANALOG, this unit reproduces the noise of an unprocessed DTS signal. When you want to play a DTS source, be sure to connect the source to a digital input jack and set the input mode to AUTO or DTS. • If you switch the input mode to ANALOG while playing a source encoded with a DTS signal, this unit reproduces no sound. • The following phenomena may occur if the input mode is set to AUTO when playing back source encoded with a DTS. - If you continue to play a source encoded with a DTS signal this unit automatically switches to the "DTSdecoding" mode to prevent noise from being generated during subsequent operation. (The "t" indicator lights up on the front panel display.) The "t" indicator may flash immediately after playback of a source encoded with a DTS signal has finished. Only a source encoded with a DTS signal can be played back while this indicator is flashing. (The indicator will flash for less than a minute.) If you want to play a normal PCM source soon, set the input mode back to AUTO. - The "t" indicator may flash when a search or skip operation is performed. If this status continues for a certain length of time, the unit will automatically switch from the "DTS-decoding" mode to PCM digital signal input mode and the "t" indicator will go out. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
26
BASIC PLAYBACK
■
Notes on playing a source
encoded with a DTS signal
•
If the digital output data of the player has been
processed in any way, you may not be able to
perform DTS decoding even if you make a digital
connection between this unit and the player.
•
If you play a source encoded with a DTS signal and
set the input mode to ANALOG, this unit reproduces
the noise of an unprocessed DTS signal. When you
want to play a DTS source, be sure to connect the
source to a digital input jack and set the input mode
to AUTO or DTS.
•
If you switch the input mode to ANALOG while
playing a source encoded with a DTS signal, this unit
reproduces no sound.
•
The following phenomena may occur if the input
mode is set to AUTO when playing back source
encoded with a DTS.
–
If you continue to play a source encoded with a DTS
signal this unit automatically switches to the “DTS-
decoding” mode to prevent noise from being
generated during subsequent operation. (The “
t
”
indicator lights up on the front panel display.) The
“
t
” indicator may flash immediately after
playback of a source encoded with a DTS signal has
finished. Only a source encoded with a DTS signal
can be played back while this indicator is flashing.
(The indicator will flash for less than a minute.) If
you want to play a normal PCM source soon, set the
input mode back to AUTO.
–
The “
t
” indicator may flash when a search or
skip operation is performed. If this status continues
for a certain length of time, the unit will
automatically switch from the “DTS-decoding”
mode to PCM digital signal input mode and the
“
t
” indicator will go out.