Yamaha HTR-5460 Owner's Manual - Page 59

Changing Parameter Settings, Resetting a Parameter to the Factory-set Value, P07 MOVIE THEATER 1

Get Yamaha HTR-5460 PDF manuals and user guides View all Yamaha HTR-5460 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

INTRODUCTION PREPARATION BASIC OPERATION Changing Parameter Settings Although it is possible to enjoy playback on your system without changing default setting parameters for the sound field program, it is also possible to enjoy specifically tailor the sound field program to the characteristics of the source and the acoustics of the listening room. 3 2 A/B/C/D/E 1 4 5 3 A/B/C/D/E 1 Set the selector dial to the DSP/TUN (or AMP/TUN) position. or 2 Turn on the video monitor and press ON SCREEN repeatedly to select the full display mode. 3 Select a DSP program you want to adjust. Program No. Program name (group) Cursor P07 MOVIE THEATER 1 70mm Spectacle P. INIT. DLY • • 13ms P. ROOM SIZE • • 1.0 S. DELAY 23ms S. ROOM SIZE • • 1.0 SOUND FIELD PROGRAM PARAMETER EDITING 4 Press u/d to select the parameter. 5 Press j / i to change the parameter value. y • When you set the parameter to a value other than the factoryset value, an asterisk mark (*) appears by the parameter name on the video monitor. 6 Repeat steps 3 to 5 above as necessary to change other program parameters. Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is set in the standby mode, the power cord is disconnected from the AC outlet, or the power supply is temporarily cut due to power failure. However, if the power is cut for more than one week, the parameter value you edited will return to the factory setting. If so, edit the parameter value again. Resetting a Parameter to the Factory-set Value Select the parameter you want to reset. Then press and hold j or i until the value temporarily stops at the factory-set value. The asterisk mark (*) by the parameter name disappears on the video monitor. Notes • The available parameters may be displayed on more than one OSD page for some of the programs. To scroll through pages, press u/d. • You cannot change parameter values when "10 MEMORY GUARD" on the SET MENU is set to ON. If you want to change the parameter values, set "10 MEMORY GUARD" to OFF. Parameters Example of the MOVIE THEATER 1 ADVANCED OPERATION ADDITIONAL INFORMATION APPENDIX English 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
55
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SOUND FIELD PROGRAM PARAMETER EDITING
SOUND FIELD PROGRAM PARAMETER EDITING
Changing Parameter Settings
Although it is possible to enjoy playback on your system
without changing default setting parameters for the sound
field program, it is also possible to enjoy specifically
tailor the sound field program to the characteristics of the
source and the acoustics of the listening room.
1
Set the selector dial to the DSP/TUN (or
AMP/TUN) position.
or
2
Turn on the video monitor
and press ON SCREEN
repeatedly to select the
full display mode.
3
Select a DSP program you want to adjust.
A/B/C/D/E
A/B/C/D/E
2
5
4
1
3
3
Program No.
Program name (group)
Cursor
Parameters
Example of the MOVIE THEATER 1
4
Press
u
/
d
to select the
parameter.
5
Press
j
/
i
to change the
parameter value.
y
•
When you set the parameter to a value other than the factory-
set value, an asterisk mark (*) appears by the parameter name
on the video monitor.
6
Repeat steps 3 to 5 above as necessary to
change other program parameters.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the parameter value you edited will
return to the factory setting. If so, edit the parameter
value again.
Resetting a Parameter to the
Factory-set Value
Select the parameter you want to reset. Then press and
hold
j
or
i
until the value temporarily stops at the
factory-set value. The asterisk mark (*) by the parameter
name disappears on the video monitor.
Notes
•
The available parameters may be displayed on more than one
OSD page for some of the programs. To scroll through pages,
press
u
/
d
.
•
You cannot change parameter values when “10 MEMORY
GUARD” on the SET MENU is set to ON. If you want to
change the parameter values, set “10 MEMORY GUARD” to
OFF.
P07 MOVIE THEATER 1
P.
INIT. DLY
• •
13ms
70mm Spectacle
S. DELAY
• • • • •
23ms
P.
ROOM SIZE
• •
1.0
S. ROOM SIZE
• •
1.0