Yamaha HTR-5460 Owner's Manual - Page 53

Setting the Manufacturer Code, To use a second and third VCR

Get Yamaha HTR-5460 PDF manuals and user guides View all Yamaha HTR-5460 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

INTRODUCTION PREPARATION BASIC OPERAIONT Setting the Manufacturer Code You can set up the code for the manufacturer of your component in each position of the selector dial. 1 Turn on your component to be used. 2 Set the selector dial to the desired position for the component (TAPE/MD, CD, DVD/LD, etc.). 3 Press j / i at the same time for about 4 seconds. The indicator flashes twice. REMOTE CONTROL FEATURES s To use a second (and third) VCR You can control a second (and third) VCR in the CBL/ SAT and DVD MENU positions if a cable TV/satellite tuner or DVD player is not being used. Note • In order to set a second (and third) VCR in the DVD MENU position, it is necessary to first set up the code for an LD player in the DVD/LD position. 1 Turn on the VCR to be used. 2 Set the selector dial to the CBL/SAT or DVD MENU position. 4 Use the numeric buttons to enter the four-digit manufacturer code for the component to be used. Make sure that the indicator flashes twice. If the indicator does not flash or flashes rapidly several times, repeat step 3 and reenter the code. 5 Press AV POWER (or any other button) to check if you have set up the code correctly. If your component cannot be controlled with the remote control, try setting another code for the same manufacturer. Notes • You can set up only one code for one position. • In the DVD/LD and DVD MENU positions: Be sure to set the selector dial to the DVD/LD position before entering the code for the DVD/LD player. You cannot set up the code for a DVD player when the selector dial is set to the DVD MENU position. The code set up in the DVD/LD position is also simultaneously set up in the DVD MENU position. • If your component does not respond to any of the codes listed for the manufacturer, use the original remote control supplied with your component. 3 Press j / i at the same time for about 4 seconds. The indicator flashes twice. 4 Use the numeric buttons to enter the four-digit code for the second (and third) VCR. Make sure that the indicator flashes twice. If the indicator does not flash or flashes rapidly several times, repeat step 3 and reenter the code. 5 Press AV POWER (or any other button) to check if you have set up the code correctly. If the VCR cannot be controlled with the remote control, try setting another code for the same manufacturer. ADVANCED OPERATION ADDITIONAL INFORMATION APPENDIX English 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
49
English
INTRODUCTION
PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
REMOTE CONTROL FEATURES
Setting the Manufacturer Code
You can set up the code for the manufacturer of your
component in each position of the selector dial.
1
Turn on your component to be used.
2
Set the selector dial to the
desired position for the
component (TAPE/MD, CD,
DVD/LD, etc.).
3
Press
j
/
i
at the same time for about
4 seconds.
The indicator flashes twice.
4
Use the numeric buttons
to enter the four-digit
manufacturer code for the
component to be used.
Make sure that the
indicator flashes twice.
If the indicator does not flash
or flashes rapidly several
times, repeat step 3 and re-
enter the code.
5
Press AV POWER (or any other button) to
check if you have set up the code correctly.
If your component cannot be
controlled with the remote
control, try setting another
code for the same
manufacturer.
Notes
•
You can set up only one code for one position.
•
In the DVD/LD and DVD MENU positions:
Be sure to set the selector dial to the DVD/LD position before
entering the code for the DVD/LD player. You cannot set up
the code for a DVD player when the selector dial is set to the
DVD MENU position. The code set up in the DVD/LD
position is also simultaneously set up in the DVD MENU
position.
•
If your component does not respond to any of the codes listed
for the manufacturer, use the original remote control supplied
with your component.
■
To use a second (and third) VCR
You can control a second (and third) VCR in the CBL/
SAT and DVD MENU positions if a cable TV/satellite
tuner or DVD player is not being used.
Note
•
In order to set a second (and third) VCR in the DVD MENU
position, it is necessary to first set up the code for an LD player
in the DVD/LD position.
1
Turn on the VCR to be used.
2
Set the selector dial to the
CBL/SAT or DVD MENU
position.
3
Press
j
/
i
at the same time for about
4 seconds.
The indicator flashes twice.
4
Use the numeric buttons
to enter the four-digit
code for the second (and
third) VCR. Make sure that
the indicator flashes
twice.
If the indicator does not flash
or flashes rapidly several
times, repeat step 3 and re-
enter the code.
5
Press AV POWER (or any other button) to
check if you have set up the code correctly.
If the VCR cannot be
controlled with the remote
control, try setting another
code for the same
manufacturer.