Yamaha RX Z9 MCXSP10 Manual - Page 108
Assigning i.LINK components, Listening to playback from an i.LINK component
UPC - 027108918204
View all Yamaha RX Z9 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 108 highlights
USING i.LINK Assigning i.LINK components When an i.LINK component is connected, this unit automatically recognizes the connection and registers the connected component. Registered i.LINK components, such as CD or DVD players, can be assigned to a specific input. Assigning an i.LINK component to a specific input allows you to select the video input signals from that component together with the audio signals received via the i.LINK connection for simultaneous playback. Notes • If you connect an i.LINK component that does not support i.LINK (AUDIO), or an i.LINK component that does not support audio signal transmission, the connected component will be registered with this unit, but cannot be assigned to a specific input. • i.LINK components without a vendor or model name, such as IEEE1394 repeater/hub, are not registered. 2 Rotate INPUT SELECTOR to select the input to which you want to assign the i.LINK component. 3 After selecting, press PURE DIRECT to complete the assignment. If two or more i.LINK components are connected simultaneously, repeat steps 2 and 3 to assign input for the other i.LINK components. y • If you do not want to assign a specific input, select "MULTI CH" in step 2, then press PURE DIRECT. If you do this, the i.LINK component is assigned to MULTI CH INPUT. Even after you assign the i.LINK component to a specific input, you can still use MULTI CH INPUT to select i.LINK (AUDIO) components using INPUT SELECTOR. • After recognition in step 1 is complete, the i.LINK component is automatically assigned to MULTI CH INPUT if no operation is performed within 10 seconds. • You can change the input assignment using the i.LINK Select menu (see page 106). STANDBY /ON PURE DIRECT 2CH/MULTI CH INPUT SELECTOR SPEAKERS A B REC OUT/ZONE 2 SOURCE/REMOTE DTV/LD DVD CABLE MD/TAPE SAT CD-R VCR 1 CD VCR 2 DVR VIDEO AUX TUNER PHONO INPUT MODE MULTI CH INPUT SILENT OPTIMIZER MIC STRAIGHT DSP PROGRAM MULTI JOG EFFECT VIDEO AUX BALANCE TONE CONTROL PHONES S VIDEO VIDEO L AUDIO R OPTICAL VOLUME 1 23 1 Turn on the power for this unit and the connected i.LINK component. The i.LINK component is automatically recognized. "Link Check" flashes on the front panel display during this procedure. MULTI CH V-AUX DVR VCR 2 VCR 1 SAT CABLE DTV/LD DVD MD/TAPE CD-R TUNER i.LINK Info. Link Check CD PHONO VOLUME LFE L CR SL SR Listening to playback from an i.LINK component Perform the following steps to listen to playback from a registered i.LINK component. If the i.LINK component has been assigned to a specific input 1 Rotate INPUT SELECTOR to select the input assigned to the i.LINK component. 2 Press INPUT MODE repeatedly to set "Auto" or "i.LINK" as the input mode. MULTI CH V-AUX DVR VCR 2 VCR 1 SAT CABLE DTV/LD Input DVD MD/TAPE CD-R DVD Auto:--- TUNER CD PHONO VOLUME LFE L CR SL SR or After the i.LINK component is recognized, the name (model number) and name of the assigned input are displayed. MULTI CH V-AUX DVR VCR 2 VCR 1 SAT CABLE DTV/LD DVD MD/TAPE CD-R DVD-AAAAA -> DVD TUNER CD PHONO VOLUME LFE L CR SL SR MULTI CH V-AUX DVR VCR 2 VCR 1 SAT CABLE DTV/LD DVD MD/TAPE CD-R TUNER CD PHONO i . L I N K A s s i g n ? VOLUME LFE ->InputSelector L SL C R SR MULTI CH V-AUX DVR VCR 2 VCR 1 SAT CABLE DTV/LD DVD MD/TAPE CD-R TUNER CD PHONO Input DVD i.LINK:--- VOLUME LFE L CR SL SR 3 Start playback on the connected i.LINK component. Refer to the operating instructions supplied with the component. 104