Zanussi ZCG63260XE User Manual - Page 22

Installation

Get Zanussi ZCG63260XE PDF manuals and user guides View all Zanussi ZCG63260XE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Problem Possible cause Remedy The flame ring is uneven. The oven does not heat up. The oven does not heat up. The oven does not heat up. The lamp does not operate. The display shows "12.00". Steam and condensation settle on the food and in the cavity of the oven. Burner crown is blocked with food residues. The oven is deactivated. The clock is not set. The necessary settings are not set. The lamp is defective. There was a power cut. You left the dish in the oven for too long. Make sure that the injector is not blocked and the burner crown is clean. Activate the oven. Set the clock. Make sure that the settings are correct. Replace the lamp. Reset the clock. Do not leave the dishes in the oven for longer than 15 - 20 minutes after the cooking process ends. SERVICE DATA If you cannot find a solution to the problem yourself, contact your dealer or an Authorised Service Centre. The necessary data for the service centre is on the rating plate. The rating plate is on the front frame of the oven cavity. Do not remove the rating plate from the oven cavity. We recommend that you write the data here: Model (MOD.) Product number (PNC) Serial number (S.N.) INSTALLATION WARNING! Refer to Safety chapters. TECHNICAL DATA ...LOCATION OF THE APPLIANCE You can install your freestanding appliance with cabinets on one or two sides and in the corner. For the minimal distances of fitting check the table. Dimensions Height Width Depth 894 - 912 mm 550 mm 609 mm 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
Problem
Possible cause
Remedy
The flame ring is uneven.
Burner crown is blocked with
food residues.
Make sure that the injector is
not blocked and the burner
crown is clean.
The oven does not heat up.
The oven is deactivated.
Activate the oven.
The oven does not heat up.
The clock is not set.
Set the clock.
The oven does not heat up.
The necessary settings are not
set.
Make sure that the settings are
correct.
The lamp does not operate.
The lamp is defective.
Replace the lamp.
The display shows "12.00".
There was a power cut.
Reset the clock.
Steam and condensation settle
on the food and in the cavity of
the oven.
You left the dish in the oven for
too long.
Do not leave the dishes in the
oven for longer than 15 - 20
minutes after the cooking
process ends.
SERVICE DATA
If you cannot find a solution to the problem yourself,
contact your dealer or an Authorised Service
Centre.
The necessary data for the service centre is on the
rating plate. The rating plate is on the front frame of
the oven cavity. Do not remove the rating plate from
the oven cavity.
We recommend that you write the data here:
Model (MOD.)
.........................................
Product number (PNC)
.........................................
Serial number (S.N.)
.........................................
INSTALLATION
WARNING!
Refer to Safety chapters.
TECHNICAL DATA
Dimensions
Height
894 - 912 mm
Width
550 mm
Depth
609 mm
LOCATION OF THE APPLIANCE
You can install your freestanding appliance with
cabinets on one or two sides and in the corner.
For the minimal distances of fitting check the table.
22