Zanussi ZCG63260XE User Manual - Page 24

Burner, Normal Power Kw, Natural Gas, Injector Mark 1/100 Mm, Btu/h, Gas Connection, Warning,

Get Zanussi ZCG63260XE PDF manuals and user guides View all Zanussi ZCG63260XE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

BURNER NORMAL POWER kW Natural Gas INJECTOR MARK 1/100 mm Btu/h Multi crown 3.4 Top Oven 1.7 Main Oven 1.7 GAS CONNECTION Use a flexible pipe in compliance with the regulation in force. Make sure they do not come in touch with mobile parts and are not squeezed. WARNING! Only a qualified and competent person can do the gas installation. Before you connect te gas, disconnect the appliance from the electricity supply or switch off the fuse in the fuse box. Close the primary valve of the gas supply. Supply piping should not be less than R3/8. Connection is made to the Rc 1/2 (1/2 " B.S.P.) female threaded. The entry pipe is located just below the hob level on the rear left hand side of the appliance. The gas supply ramp is on the rear side of the appliance. WARNING! Only liquid sealants can be used when the inlet gas pipe is fitted i.e.: do not use the P.T.F.E. sealant tape. When the installation is complete, carry out a gas tightness test and make sure that the seal of each pipe fitting does not leak. Use flexible tubing, which comply with the BS.669 current edition. 136 11600 95 5804 95 5804 A E B D C C WARNING! The gas bayonet connector must be in the marked area. Dimension mm A 250 B 680 C 50 D 250 E 580 PRESSURE TEST The Rapid injector is used as a pressure test point. 1. Connect the pressure gauge to the Rapid injector. 2. Examine the supply pressure by turning the Rapid burner and one other burner fully on, and lighting them. The pressure must be 20 mbar for Natural Gas. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
BURNER
NORMAL POWER kW
Natural Gas
INJECTOR MARK 1/100 mm
Btu/h
Multi crown
3.4
136
11600
Top Oven
1.7
95
5804
Main Oven
1.7
95
5804
GAS CONNECTION
Use a flexible pipe in compliance with the
regulation in force. Make sure they do not come in
touch with mobile parts and are not squeezed.
WARNING!
Only a qualified and
competent person can do the gas
installation.
Before you connect te gas, disconnect
the appliance from the electricity
supply or switch off the fuse in the
fuse box. Close the primary valve of
the gas supply.
Supply piping should not be less than
R3/8. Connection is made to the Rc
1/2 (1/2 “ B.S.P.) female threaded.
The entry pipe is located just below
the hob level on the rear left hand side
of the appliance.
The gas supply ramp is on the rear
side of the appliance.
WARNING!
Only liquid sealants can
be used when the inlet gas pipe is
fitted i.e.: do not use the P.T.F.E.
sealant tape.
When the installation is complete,
carry out a gas tightness test and
make sure that the seal of each pipe
fitting does not leak.
Use flexible tubing, which comply with
the BS.669 current edition.
A
B
C
C
D
E
WARNING!
The gas bayonet
connector must be in the marked area.
Dimension
mm
A
250
B
680
C
50
D
250
E
580
PRESSURE TEST
The Rapid injector is used as a pressure test point.
1.
Connect the pressure gauge to the Rapid
injector.
2.
Examine the supply pressure by turning the
Rapid burner and one other burner fully on, and
lighting them. The pressure must be 20 mbar
for Natural Gas.
24