Home » ZyXEL Manuals » Networking » ZyXEL PLA-450 » Manual Viewer

ZyXEL PLA-450 User Guide - Page 73

Table 16, Wireless LAN, PLA450 User's Guide

Get ZyXEL PLA-450 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Figure 38 Network > Wireless LAN > Advanced Chapter 6 Wireless LAN The following table describes the labels in this screen. Table 16 Network > Wireless LAN > Advanced LABEL DESCRIPTION Roaming Configuration Enable Roaming Select this option if your network environment has multiple APs and you want your wireless device to be able to access the network as you move between wireless networks. Wireless Advanced Setup RTS/CTS Threshold Data with its frame size larger than this value will perform the RTS (Request To Send)/CTS (Clear To Send) handshake. If the RTS/CTS value is greater than the Fragmentation Threshold value, then the RTS/CTS handshake will never occur as data frames will be fragmented before they reach RTS/CTS size. Enter a value between 256 and 2346. See Appendix D on page 159 for more information. Fragmentation It is the maximum data fragment size that can be sent. Enter a value between 256 Threshold and 2346. See Appendix D on page 159 for more information. Enable IntraBSS Traffic A Basic Service Set (BSS) exists when all communications between wireless clients or between a wireless client and a wired network client go through one access point (AP). Intra-BSS traffic is traffic between wireless clients in the BSS. When Intra-BSS is enabled, wireless client A and B can access the wired network and communicate with each other. When Intra-BSS is disabled, wireless client A and B can still access the wired network but cannot communicate with each other. See Appendix D on page 159 for more information. Output Power Set the output power of the PLA450 in this field. If there is a high density of APs within an area, decrease the output power of the PLA450 to reduce interference with other APs. PLA450 User's Guide 73

Section	Page
PLA450 Series	1
User’s Guide	1
About This User's Guide	3
Document Conventions	4
Safety Warnings	6
Contents Overview	9
Table of Contents	11
List of Figures	15
List of Tables	19
Introduction	21
Getting to Know Your PLA450	23
1.1 Overview	23
1.1.1 Wireless LAN Application	23
1.1.2 HomePlug AV	23
1.2 Ways to Manage the PLA450	24
1.3 Good Habits for Managing the PLA450	24
1.4 LEDs	25
The WPS Button	27
2.1 Overview	27
2.2 Push Button Configuration	27
The ENCRYPT Button	29
3.1 ENCRYPT Button Overview	29
3.2 Set Up a HomePlug AV Network with ENCRYPT	29
3.3 Setting Up Multiple Networks	31
3.4 ENCRYPT Button Behavior	32
Introducing the Web Configurator	35
4.1 Web Configurator Overview	35
4.2 Accessing the Web Configurator	35
4.3 Resetting the PLA450	37
4.3.1 Procedure to Use the Reset Button	37
4.4 Navigating the Web Configurator	37
4.4.1 The Status Screen	37
4.4.2 Navigation Panel	40
4.4.3 Summary: Packet Statistics	41
4.4.4 Summary: Wireless Station Status	42
4.4.5 Summary: My HomePlug Network Status	42
Wireless Tutorial	47
5.1 Example Parameters	47
5.2 Configuring the PLA450	47
5.3 Configuring the Wireless Client	49
5.3.1 Connecting to a Wireless LAN	49
5.3.2 Creating and Using a Profile	52
Network	55
Wireless LAN	57
6.1 Wireless Network Overview	57
6.2 Wireless Security Overview	59
6.2.1 SSID	59
6.2.2 MAC Address Filter	59
6.2.3 User Authentication	59
6.2.4 Encryption	60
6.3 Roaming	61
6.3.1 Requirements for Roaming	62
6.4 Quality of Service	62
6.4.1 WMM QoS	63
6.5 WPS Overview	63
6.5.1 WPS Setup Using a PIN	64
6.5.2 How WPS Works	65
6.5.3 Limitations of WPS	67
6.6 General Wireless LAN Screen	68
6.6.1 No Security	69
6.6.2 WPA-PSK/WPA2-PSK	70
6.7 MAC Filter	71
6.8 Wireless LAN Advanced Screen	72
6.9 Quality of Service (QoS) Screen	74
6.9.1 Application Priority Configuration	76
6.10 WPS Screen	77
6.11 WPS Station Screen	78
LAN	81
7.1 LAN Overview	81
7.1.1 Factory LAN Defaults	81
7.1.2 IP Address	81
7.1.3 IP Address and Subnet Mask	82
7.2 LAN IP Screen	82
HomePlug AV	85
8.1 Overview	85
8.2 Privacy and Powerline Adapters	86
8.2.1 Setting Up a Private Powerline Network	87
8.2.2 Setting Up Multiple Powerline Networks.	87
8.3 Configuring Your HomePlug AV Devices	88
8.4 HomePlug AV QoS	91
8.4.1 QoS Based on IP or MAC Address	91
8.4.2 Mapping other QoS Priority Settings to HomePlug AV QoS	91
8.4.3 QoS Based on Traffic Type	92
Maintenance and Troubleshooting	95
System	97
9.1 System General Screen	97
9.2 Time Setting Screen	98
Logs	101
10.1 View Log	101
10.2 Log Settings	102
Tools	105
11.1 Firmware Upload Screen	105
11.2 Configuration Screen	107
11.2.1 Backup Configuration	107
11.2.2 Restore Configuration	107
11.2.3 Back to Factory Defaults	108
11.3 Restart Screen	109
Configuration Mode	111
Language	113
13.1 Selecting Language	113
Troubleshooting	115
14.1 Power, Hardware Connections, and LEDs	115
14.2 PLA450 Access and Login	116
14.3 Internet Access	117
14.4 Resetting the PLA450 to Its Factory Defaults	118
14.5 Wireless Troubleshooting	119
14.6 HomePlug AV Troubleshooting	119
14.7 ENCRYPT Button Problems	120
14.8 Advanced Features	121
Product Specifications and Wall- Mounting Instructions	123
Appendices and Index	127
Pop-up Windows, JavaScripts and Java Permissions	129
IP Addresses and Subnetting	135
Setting up Your Computer’s IP Address	143
15.0.1 Verifying Settings	158
Wireless LANs	159
Common Services	173
Legal Information	177
Customer Support	181