ZyXEL UAG50 User Guide - Page 10

Reset Button, Power Jack

Get ZyXEL UAG50 PDF manuals and user guides View all ZyXEL UAG50 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

UAG50 User's Guide Off: A port has not established any network connection. Yellow light: A port has established a valid 10/100 Mbps network connection. Yellow Blinking: 10/100 Mbps traffic is traversing the port.  Reset Button: The UAG50 has a reset button at the rear panel of the device. Use this function to reset the system back to factory defaults.  Power Jack: Used to connect the external power supply with the UAG50. 1-4-1 Printing a test page After you have installed your printer, you should print a test page to make sure the printer is functioning properly. To do this act as follows: 1. Turn the printer off. 2. Hold down the button A for approximately five seconds, and then turn the printer on. 3. The printer will print a test page. 1-4-2 How to load paper rolls Please follow the steps to correctly load paper rolls. 1 2 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
UAG50 User’s Guide
10
Off: A port has not established any network connection.
Yellow light: A port has established a valid 10/100 Mbps network
connection.
Yellow Blinking: 10/100 Mbps traffic is traversing the port.
Reset Button:
The UAG50 has a reset button at the rear panel of the device.
Use this function
to reset the system back to factory defaults.
Power Jack:
Used to connect the external power supply with the UAG50.
1-4-1
Printing a test page
After you have installed your printer, you should print a test page to make sure the
printer is functioning properly. To do this act as follows:
1.
Turn the printer off.
2.
Hold down the button A for approximately five seconds, and then turn the
printer on.
3.
The printer will print a test page.
1-4-2
How to load paper rolls
Please follow the steps to correctly load paper rolls.
1
2