Adaptec AHA-2742T User Manual - Page 43

AHA-2740 Series User's Manual

Get Adaptec AHA-2742T - Storage Controller Fast SCSI 10 MBps PDF manuals and user guides View all Adaptec AHA-2742T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

AHA-2740 Series User's Manual connector. To connect SCSI devices to SCSI channel A, you will need either an internal SCSI cable and/or external SCSI cable. To connect SCSI devices to SCSI Channel B, you will need only an internal SCSI cable. Connecting Internal SCSI Devices The internal connector for your host adapter uses a 50-pin SCSI ribbon cable with a 50-pin header internal connector. When connecting the 50-pin internal SCSI ribbon cable to both the host adapter and to the internal SCSI device(s), make sure that Pin 1 orientation is maintained throughout the bus. Pin 1 of the SCSI cable is designated by a colored stripe on one edge of the ribbon cable. Pin 1 of the host adapter or SCSI device connector is usually designated by a delta or arrow symbol (v) on the connector. Note Refer to the manufacturer's instructions to install and mount internal SCSI devices inside your computer chassis. To connect internal SCSI devices: ® 1 Connect one end of the 50-pin SCSI ribbon cable to the internal connector on the host adapter, as shown in Figure 2-6. 2-16 Adaptec AHA-2740 Series User's Manual Stock Number: 510381-00 / Rev. C (Page 2-16) Print Spec Number: 491709-00 Rev C Current Date: 9/1/93 ECN Date: 9/14/93

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
connector. To connect SCSI devices to SCSI channel A, you will
need either an internal SCSI cable and/or external SCSI cable. To
connect SCSI devices to SCSI Channel B, you will need only an
internal SCSI cable.
Connecting Internal SCSI Devices
The internal connector for your host adapter uses a 50-pin SCSI
ribbon cable with a 50-pin header internal connector.
When connecting the 50-pin internal SCSI ribbon cable to both the
host adapter and to the internal SCSI device(s), make sure that Pin
1 orientation is maintained throughout the bus. Pin 1 of the SCSI
cable is designated by a colored stripe on one edge of the ribbon
cable. Pin 1 of the host adapter or SCSI device connector is usually
designated by a delta or arrow symbol (
▲
) on the connector.
Note
Refer to the manufacturer’s instructions to install and mount
internal SCSI devices inside your computer chassis.
To connect internal SCSI devices:
1
Connect one end of the 50-pin SCSI ribbon cable to the internal
connector on the host adapter, as shown in Figure 2-6.
Adaptec AHA-2740 Series User’s Manual
Stock Number:
510381-00
/
Rev. C
(Page 2-16)
Print Spec Number:
491709-00 Rev C
Current Date:
9/1/93
ECN Date:
9/14/93
AHA-2740 Series User’s Manual
2-16