Adaptec AHA-2742T User Manual - Page 79

h - Data protect

Get Adaptec AHA-2742T - Storage Controller Fast SCSI 10 MBps PDF manuals and user guides View all Adaptec AHA-2742T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

AHA-2740 Series User's Manual 06h - Data protect The removable media may be write-protected. Remove write protection and run the utility again. The Additional Sense Code field provides more information about the error. The meaning of these codes may be listed in your hardware manual. My computer locks up when I press Esc to exit the EISA Configuration utility. If this happens, turn your machine off and then on to reboot. Any settings you changed before you tried to exit the program have been registered in the EEPROM and will not be lost. One of the SCSI devices on my system does not allow termination to be disabled. How can I attach it to the SCSI bus? You might be able to attach this device on the end of the SCSI bus so you do not need to disable termination on it. If this is not possible, contact the manufacturer about possible work-arounds. I installed my host adapter board at IRQ12, and it does not work properly. What is wrong? Another device such as a mouse may be using IRQ12. Change the adapter board's IRQ to the default value (11) or to some other value. See Configure the Host Adapter Parameters in Chapter 3. When I install my host adapter it either does not get automatically added by my EISA Configuration utility, or an error is reported by the motherboard as not being a valid board, even after running the EISA Configuration utility. Verify that you are using the correct .cfg file and .ovl file for the host adapter. Also, other EISA boards and their position on the bus could be causing the board to be mis-identified. 4-6 Adaptec AHA-2740 Series User's Manual Stock Number: 510381-00 / Rev. C (Page 4-6) Print Spec Number: 491709-00 Rev C Current Date: 9/1/93 ECN Date: 9/14/93

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
06h - Data protect
The removable media may be write-protected. Remove write
protection and run the utility again.
The Additional Sense Code field provides more information about
the error. The meaning of these codes may be listed in your
hardware manual.
My computer locks up when I press Esc to exit the EISA Configuration
utility.
If this happens, turn your machine off and then on to reboot. Any
settings you changed before you tried to exit the program have
been registered in the EEPROM and will not be lost.
One of the SCSI devices on my system does not allow termination to
be disabled. How can I attach it to the SCSI bus?
You might be able to attach this device on the end of the SCSI
bus so you do not need to disable termination on it. If this is not
possible, contact the manufacturer about possible work-arounds.
I installed my host adapter board at IRQ12, and it does not work
properly. What is wrong?
Another device such as a mouse may be using IRQ12. Change the
adapter board’s IRQ to the default value (11) or to some other
value. See
Configure the Host Adapter Parameters
in Chapter 3.
When I install my host adapter it either does not get automatically
added by my EISA Configuration utility, or an error is reported by the
motherboard as not being a valid board, even after running the EISA
Configuration utility.
Verify that you are using the correct
.cfg
file and
.ovl
file for the
host adapter. Also, other EISA boards and their position on the
bus could be causing the board to be mis-identified.
Adaptec AHA-2740 Series User’s Manual
Stock Number:
510381-00
/
Rev. C
(Page 4-6)
Print Spec Number:
491709-00 Rev C
Current Date:
9/1/93
ECN Date:
9/14/93
AHA-2740 Series User’s Manual
4-6