Belkin KVM over IP User Manual - Page 30

Connecting the servers - reset

Get Belkin KVM over IP - Omniview SMB 1x16 Switch KVM PDF manuals and user guides
UPC - 722868596104
View all Belkin KVM over IP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

section Local Installation Connecting the servers: 1. Connect all servers to the SMB KVM-over-IP Switch and secondary KVM 1 Switches. Refer to the "Connecting Servers to the Switch" section on page 16 for instructions. 2 2. Make sure that the power adapter is connected to the SMB KVM-over-IP Switch and that the Switch is powered on. You should see the Switch light 3 up and display the digits "00", indicating its BANK address. 3. Power up the secondary KVM Switches sequentially, beginning with BANK 01, by connecting each unit's power supply. Each KVM Switch should 4 display its corresponding BANK address number as it is powered up. 5 Note: If the secondary KVM Switches do not enumerate correctly, reset the SMB KVM-over-IP Switch (BANK 00) by simultaneously pressing the "BANK +" and "BANK -" buttons. You can also reset the primary switch 6 to detect newly added secondary KVM Switches. If the KVM Switches still do not enumerate correctly, check that all KVM Switches have the 7 correct BANK address assigned to them and that all daisy-chain cables are connected properly. 4. Verify that the SMB KVM-over-IP Switch has detected all secondary 8 KVM Switches by scrolling through the BANKs using the "BANK +" and "BANK -" buttons. If all secondary KVM Switches are detected properly, the LED display on the primary KVM Switch will register and display the 9 BANK address of the attached secondary KVM Switch. 10 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
27
1
2
3
4
5
6
7
8
9
10
section
27
27
Local Installation
Connecting the servers:
1.
Connect all servers to the SMB KVM-over-IP Switch and secondary KVM
Switches. Refer to the “Connecting Servers to the Switch” section on page
16 for instructions.
2.
Make sure that the power adapter is connected to the SMB KVM-over-IP
Switch and that the Switch is powered on. You should see the Switch light
up and display the digits “00”, indicating its BANK address.
3.
Power up the secondary KVM Switches sequentially, beginning with BANK
01, by connecting each unit’s power supply. Each KVM Switch should
display its corresponding BANK address number as it is powered up.
Note:
If the secondary KVM Switches do not enumerate correctly, reset
the SMB KVM-over-IP Switch (BANK 00) by simultaneously pressing the
“BANK +” and “BANK –” buttons. You can also reset the primary switch
to detect newly added secondary KVM Switches. If the KVM Switches
still do not enumerate correctly, check that all KVM Switches have the
correct BANK address assigned to them and that all daisy-chain cables are
connected properly.
4.
Verify that the SMB KVM-over-IP Switch has detected all secondary
KVM Switches by scrolling through the BANKs using the “BANK +” and
“BANK –” buttons. If all secondary KVM Switches are detected properly,
the LED display on the primary KVM Switch will register and display the
BANK address of the attached secondary KVM Switch.