Belkin KVM over IP User Manual - Page 61

Using the Switch from a Local Console - single port

Get Belkin KVM over IP - Omniview SMB 1x16 Switch KVM PDF manuals and user guides
UPC - 722868596104
View all Belkin KVM over IP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Using the Switch from a Local Console Now that you have connected your console and servers to the Switch, it is ready for use. You can select connected servers by using either the front-panel port selectors, the On-Screen Display (OSD), or hot-key commands through the console keyboard. It takes approximately 1-2 seconds for the video signal to refresh after switching servers. Re-synchronization of the mouse and keyboard signals also occurs. This is normal operation and ensures that proper synchronization is established between the console and the connected servers. Selecting a Server or BANK Selecting a Server or BANK Using Hot Keys Switch to the next or previous port with simple keyboard hot-key sequences using the Scroll Lock key and either the up or down arrow keys. To send commands to the Switch, the Scroll Lock key must be pressed twice within two seconds. The Switch will beep, confirming that it is in hot-key mode. Next, press the up arrow key and the Switch will switch to the next port. Press the down arrow key to switch to the previous port. Switch to next active port, "Up" arrow. Switch to previous active port, "Down" arrow With a single-switch configuration (no daisy-chained KVM switches), you can switch directly to any port by entering the 2-digit number of the port you wish to access. For example, if you press "Scroll Lock", "Scroll Lock", "02", the Switch will switch to the server on port 2 located on BANK 00. Switch to BANK 00, Port 2 (02) 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
58
Using the Switch from a Local Console
Now that you have connected your console and servers to the Switch,
it is ready for use. You can select connected servers by using either the
front-panel port selectors, the On-Screen Display (OSD), or hot-key commands
through the console keyboard. It takes approximately 1–2 seconds for the video
signal to refresh after switching servers. Re-synchronization of the mouse and
keyboard signals also occurs. This is normal operation and ensures that proper
synchronization is established between the console and the connected servers.
Selecting a Server or BANK
Selecting a Server or BANK Using Hot Keys
Switch to the next or previous port with simple keyboard hot-key sequences
using the Scroll Lock key and either the up or down arrow keys. To send
commands to the Switch, the Scroll Lock key must be pressed twice within two
seconds. The Switch will beep, confirming that it is in hot-key mode. Next, press
the up arrow key and the Switch will switch to the next port. Press the down
arrow key to switch to the previous port.
Switch to previous active port,
“Down” arrow
Switch to next active port, “Up” arrow.
With a single-switch configuration (no daisy-chained KVM switches), you can
switch directly to any port by entering the 2-digit number of the port you wish to
access. For example, if you press “Scroll Lock”, “Scroll Lock”, “02”, the Switch
will switch to the server on port 2 located on BANK 00.
Switch to BANK 00, Port 2 (02)