Bosch B20CS80SNB Operating Instructions - Page 20

Installation, instructions

Get Bosch B20CS80SNB - Evolution 800 Series 20 cu. Ft. Refrigerator PDF manuals and user guides View all Bosch B20CS80SNB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Installation instructions Important information: These installation instructions refer to various models. Not all steps are required for some models. The appliance should only be installed and connected by a recognized specialist according to these installation instructions. Always connect the water before the power. In addition to the statutory national regulations, observe the connection conditions of the electricity and water supply companies. Keep the installation instructions in a safe place. If installation next to a heat source is unavoidable, use a suitable insulating plate or observe the following minimum distances to a heat source: - 11/4" (3 cm) to an electric cooker. - from an oil or solidĆfuel cooker 113/16" (30 cm). The floor on which the appliance is to be installed must be rigid. If required, reinforce the floor. To ensure that the ice maker functions correctly, the appliance must be upright. To ensure that the doors can open all the way, observe lateral minimum distances when installing the appliance in a corner or recess (see section on Appliance and installation dimensions"). q After installing the appliance, remove the transportation protection devices from the ice maker. To do this, pull out the ice maker. Warning: Before connecting the appliance to the power supply, remove all the inner and outer packaging material. Installation location Warning: The appliance is very heavy, for empty weight see the following table. Basic model 229 lbs (104 kg) Model with dispenser 248.5 lbs (113 kg) Install the appliance in a dry, well ventilated room. The installation location should neither be exposed to direct sunlight nor near a heat source, e.g. a cooker, radiator, etc. Unpacking the appliance q Remove packaging material and adhesive tape. (Adhesive residue on the housing can be removed with the adhesive side of the removed tape. To do this, repeatedly place the adhesive tape on the adhesive residue and remove). q Do not remove the transportation protection devices from the shelves and storage compartments until the appliance has been installed. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
20
Installation
instructions
Important information:
These installation
instructions refer
to various
models.
Not
all
steps
are required for
some
models.
The appliance
should
only be
installed
and connected
by
a±recognized
specialist
according
to
these installation
instructions.
Always
connect the
water before
the power.
In addition
to
the
statutory
national
regulations,
observe the
connection
conditions
of the
electricity
and water supply
companies.
Keep
the
installation
instructions
in
a safe
place.
Installation location
Warning:
The appliance
is
very
heavy,
for
empty
weight see
the
following
table.
Basic± model
229± lbs
(104 kg)
Model
± with
± dispenser
248.5
± lbs
(113 kg)
Install
the
appliance
in
a
dry,
well
ventilated
room. The installation
location should neither
be
exposed
to direct
sunlight nor near
a
heat
source,
e.g. a
cooker,
radiator, etc.
If²installation
next
to
a heat
source
is
unavoidable,
use a suitable
insulating
plate
or
observe the
following
minimum
distances
to
a²heat
source:
-
1
1
/
4
" (3
cm) to
an
electric
cooker.
-
from an
oil or
solidĆfuel
cooker
11
3
/
16
" (30²cm).
The
floor
on which
the
appliance
is
to
be
installed
must be rigid.
If²required, reinforce
the
floor.
To
ensure that
the
ice
maker
functions correctly,
the
appliance
must be upright.
To
ensure
that
the
doors can open
all
the
way,
observe
lateral minimum
distances
when
installing
the
appliance
in
a²corner
or
recess (see section
on ±Appliance
and installation
dimensions").
Unpacking the
appliance
q
Remove packaging
material
and
adhesive
tape.
(Adhesive
residue on the
housing
can
be
removed with
the
adhesive
side
of
the
removed
tape.
To
do
this,
repeatedly place
the
adhesive
tape
on the
adhesive
residue
and
remove).
q
Do
not remove the
transportation
protection
devices
from the
shelves
and
storage compartments
until
the
appliance
has
been
installed.
q
After
installing
the
appliance,
remove the
transportation
protection
devices
from
the ice
maker.
To
do
this,
pull out
the
ice
maker.
Warning:
Before connecting
the
appliance to
the
power
supply, remove
all the
inner
and
outer
packaging
material.