Brother International HS-5300 Users Manual - English - Page 24

Loading Paper into the Feeder

Get Brother International HS-5300 PDF manuals and user guides View all Brother International HS-5300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

English: HS3 User's Guide, Chapter 2 USER'S GUIDE Loading Paper into the Feeder To load paper into the feeder, follow these steps. 1. Pull the cover of the sheet feeder forward. 2. Load paper into the sheet feeder with the printing surface face up.  Caution  The feeder can hold up to 200 sheets of 80 g/m2 (20 lb.) plain paper. If you load too many sheets, paper jams could occur.  Make sure that the paper is stacked below the w mark.  If there is still some paper left in the feeder, you must first remove it, put it together with the new paper and then insert the stack into the feeder.  Note  When you load envelopes in the feeder, make sure they are inserted in the direction shown below. The Stamp corner at the lower right hand corner of the envelope should face the front of the printer.  The first feeder can hold up to 10 sheets of envelopes and you can load an envelope sheet by sheet into a manual feed slot.  Set the head gap lever to the 'Envelope and Transparency' position. Fig. 2-4 Loading Envelopes in the Feeder 2-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
USER’S GUIDE
2–6
English: HS3 User’s Guide, Chapter 2
Loading Paper into the Feeder
To load paper into the feeder, follow these steps.
1.
Pull the cover of the sheet feeder forward.
2.
Load paper into the sheet feeder with the printing surface face up.
Caution
The feeder can hold up to 200 sheets of 80 g/m
2
(20 lb.) plain paper. If you
load too many sheets, paper jams could occur.
Make sure that the paper is stacked below the
▼
mark.
If there is still some paper left in the feeder, you must first remove it, put it
together with the new paper and then insert the stack into the feeder.
Note
When you load envelopes in the feeder, make sure they are inserte
d
in the
direction shown below. The Stamp corner at the lower right hand corner of
the envelope should face the front of the printer.
The first feeder can hold up to 10 sheets of envelopes and you can load an
envelope sheet by sheet into a manual feed slot.
Set the head gap lever to the ‘Envelope and Transparency’ position.
Fig. 2-4
Loading Envelopes in the
Feeder