Brother International LK3-B434E MKII Instruction Manual - English - Page 12

Installing the control box

Get Brother International LK3-B434E MKII PDF manuals and user guides View all Brother International LK3-B434E MKII manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

3-4. Installing the control box !0 !1 !2 w 3. INSTALLATION r t y u i o 3 mm Table t Cushions y Cushion collars u Rubber collers i Flat washers o Nuts e q !3 1. Remove the 12 screws q, and then open the covers (panel mounting assembly w and main P.C. board mounting plate e). NOTE: When opening the cover, hold it securely so that it does not fall down. 2. Install the control box with the four accessory bolts r, cushions t, cushion collars y, rubber collars u, flat washers i and nuts o as shown in the illustration above. At this time, leave a gap of approximately 3 mm between the work table and the top of the box. * Use two nuts o at each installation location, and make sure that both nuts are tightened. 3. Close the covers (panel mounting assembly w and main P.C. board mounting plate e), and tighten them with the screws q. * The main P.C. board mounting plate e will be opened again during "3-13. Connecting the cords", so provisionally tighten it with the screw q. 4. Install the power switch !0 with the two screws !1. 5. Secure the power switch cord with the three staples !.2 6. Pass the motor cord through the cord hole !.3 LK3-B434E Mark II 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
6
LK3-B434E Mark II
3. INSTALLATION
!
0
!
1
!
2
w
e
q
o
i
u
y
t
r
t
u
i
o
y
Table
Cushions
Cushion collars
Nuts
Flat washers
Rubber collers
3 mm
!
3
3-4. Installing the control box
1.
Remove the 12 screws
q
, and then open the covers (panel mounting assembly
w
and main P.C. board
mounting plate
e
).
NOTE:
When opening the cover, hold it securely so that it does not fall down.
2.
Install the control box with the four accessory bolts
r
, cushions
t
, cushion collars
y
, rubber collars
u
,
flat washers
i
and nuts
o
as shown in the illustration above. At this time, leave a gap of approximately 3
mm between the work table and the top of the box.
*
Use two nuts
o
at each installation location, and make sure that both nuts are tightened.
3.
Close the covers (panel mounting assembly
w
and main P.C. board mounting plate
e
), and tighten them
with the screws
q
.
* The main P.C. board mounting plate
e
will be opened again during
“
3-13. Connecting the cords
”
, so
provisionally tighten it with the screw
q
.
4.
Install the power switch
!0
with the two screws
!1
.
5.
Secure the power switch cord with the three staples
!
2
.
6.
Pass the motor cord through the cord hole
!3
.