Brother International LK3-B434E MKII Instruction Manual - English - Page 65

Setting reverse work clamp mode, SETTING THE WORK CLAMP MODE, Basic setting, Notes to sewing]

Get Brother International LK3-B434E MKII PDF manuals and user guides View all Brother International LK3-B434E MKII manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

14. SETTING THE WORK CLAMP MODE 14-4. Setting reverse work clamp mode Basic setting 1. If installing the inner clamping device as a later option, set the memory switches as follows. (This will complete inner clamping specification settings.) • Set the memo-07 switch to ON. • Set the memo-42 switch to "5". 2. Make the following settings if necessary. 1. 1/2 reverse mode The inner clamping device operates at the 1/2-way mark for the pattern being sewn. Example start reverse memo-13 - 2. 1/4 reverse mode The inner clamping device operates at the 1/4-way and 3/4-way marks for the pattern being sewn. Example end [Notes to sewing] 4.5 mm start reverse reverse memo-13 ON Reference point 4.5 mm 1. Reverse stitching is possible within 4.5 mm left and right from the reference point. However, note that if a non-standard work clamp is being used, the reverse stitching area will become smaller. Lift 15 mm Thickness of material 59 q 19 mm 2. When the work clamp q reverses after sewing is completed, the work clamps are retracted so that they do not touch the needle. However, sometimes it is not necessary to retract the work clamps if the material is thin. In such cases, if memory switch memo-15 is set to on, the work clamps will not be retracted so that the cycle time can be shortened. However, if making this change to the setting, move the work clamp to the sewing end position (release the air and move the work clamp by hand) to check that the work clamps do not touch the needle. LK3-B434E Mark II

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
59
LK3-B434E Mark II
14. SETTING THE WORK CLAMP MODE
1.
Reverse stitching is possible within 4.5 mm left and
right from the reference point.
However, note that if a non-standard work clamp
is being used, the reverse stitching area will be-
come smaller.
14-4. Setting reverse work clamp mode
q
–
memo-13
ON
memo-13
Basic setting
1.
If installing the inner clamping device as a later option, set the memory switches as follows.
(This will complete inner clamping specification settings.)
•
Set the memo-07 switch to ON.
•
Set the memo-42 switch to
“
5
”
.
2.
Make the following settings if necessary.
1.
1/2 reverse mode
The inner clamping device operates at the 1/2-way mark for the pattern being sewn.
Example
2.
1/4 reverse mode
The inner clamping device operates at the 1/4-way and 3/4-way marks for the pattern being sewn.
Example
[Notes to sewing]
Reference point
4.5 mm
4.5 mm
19 mm
15 mm
Lift
Thickness of material
start
reverse
start
reverse
end
reverse
2.
When the work clamp
q
reverses after sewing is
completed, the work clamps are retracted so that
they do not touch the needle. However, sometimes
it is not necessary to retract the work clamps if the
material is thin.
In such cases, if memory switch memo-15 is set to
on, the work clamps will not be retracted so that
the cycle time can be shortened. However, if mak-
ing this change to the setting, move the work clamp
to the sewing end position (release the air and
move the work clamp by hand) to check that the
work clamps do not touch the needle.