Canon FAXPHONE L120 FAXPHONE L120 Advanced Guide - Page 17

Memory Reception, Use [Up/Down] to select <1 MEMORY RX - toner

Get Canon FAXPHONE L120 PDF manuals and user guides View all Canon FAXPHONE L120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Advanced Fax Features 1 Status Monitor 2 Reports and Lists 3 Troubleshooting 4 Appendix 5 5. Press [Stop/Reset] to return to standby mode. FAX/TEL: Optional Settings If required, change the optional settings as follows: : Use the numeric buttons to enter the duration (0 to 30 seconds) for which the machine listens for the fax tone before it starts ringing. Press [Set]. : Use the numeric buttons to enter the duration (10 to 45 seconds) of ringing. Press [Set]. : Use [Left/Right] to select the default action the machine will take after the ringing ends, then press [Set]. - : Tries to receive the document. - : Disconnects the call. AnsMode: Optional Settings If required, change the optional settings as follows: : Use the numeric buttons to enter the duration (10 to 30 seconds) for which the machine waits until the connected answering machine takes the call. Press [Set]. : Use the numeric buttons to enter the duration (10 to 70 seconds) for which the machine attempts to detect the fax tone. Press [Set]. Back Previous Next TOP ■ Memory Reception The machine automatically receives faxes in memory when printing is disabled under certain conditions (i.e., toner or paper has run out). You can also set the machine to receive faxes in memory during a certain time period of your choice, with password protection if required. 1. Press [Menu]. 2. Use [Up/Down] to select , then press [Set]. 3. Use [Up/Down] to select , then press [Set]. 4. Use [Left/Right] to select , then press [Set]. Table of Contents Index 1-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
1
2
3
4
5
TOP
Back
Previous
Next
1-7
Advanced Fax
Features
Status Monitor
Reports and Lists
Troubleshooting
Appendix
Table of Contents
Index
5.
Press [Stop/Reset] to return to standby mode.
FAX/TEL: Optional Settings
If required, change the optional settings as follows:
<SET RING START TIME>: Use the numeric buttons to enter
the duration (0 to 30 seconds) for which the machine listens for
the fax tone before it starts ringing. Press [Set].
<SET F/T RING TIME>: Use the numeric buttons to enter the
duration (10 to 45 seconds) of ringing. Press [Set].
<SET DEFAULT ACTION>: Use [Left/Right] to select the default
action the machine will take after the ringing ends, then press
[Set].
–
<RECEIVE>: Tries to receive the document.
–
<DISCONNECT>: Disconnects the call.
AnsMode: Optional Settings
If required, change the optional settings as follows:
<SET CHECK TAD TIME>: Use the numeric buttons to enter the
duration (10 to 30 seconds) for which the machine waits until the
connected answering machine takes the call. Press [Set].
<SET FAX DETECT TIME>: Use the numeric buttons to enter
the duration (10 to 70 seconds) for which the machine attempts
to detect the fax tone. Press [Set].
■
Memory Reception
The machine automatically receives faxes in memory when
printing is disabled under certain conditions (i.e., toner or paper
has run out). You can also set the machine to receive faxes in
memory during a certain time period of your choice, with
password protection if required.
1.
Press [Menu].
2.
Use [Up/Down] to select <RX SETTING?>, then
press [Set].
3.
Use [Up/Down] to select <1 MEMORY RX
MODE?>, then press [Set].
4.
Use [Left/Right] to select <ON>, then press
[Set].