Canon PIXMA MP800 MP800 User's Guide - Page 131

Error Message On Camera, Action

Get Canon PIXMA MP800 PDF manuals and user guides View all Canon PIXMA MP800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 131 highlights

Error Message On Camera Printer in use/Printer warming up Action Photos are printed from the computer. Wait until printing ends. When it is ready, the machine starts printing automatically. No paper/Paper Error Paper jam z Load paper in either the Auto Sheet Feeder or Cassette which you have selected with [Feed Switch] on the machine, and select "Continue"*1 in the display on your camera. z The camera does not support the page size that is selected on this machine. Check the print settings and select the page size that is supported by the camera. z Open the Paper Output Tray to resume printing. Close the Inner Cover if it is open. Select "Stop" in the display on your camera to stop printing. Select "Stop" in the display on your camera to stop printing. Remove the jammed paper, load new paper, and press [OK] on the machine and retry printing. Printer cover open Close the Scanning Unit (Printer Cover) on the machine. No print head The Print Head is defective or not installed. Install a Print Head according to the Easy Setup Instructions. If the Print Head has already been installed, remove the Print Head and reinstall it. If the error still remains, the Print Head may be defective. Contact the Canon Customer Care Center. Waste tank (ink absorber) full This error message indicates that the waste ink absorber is nearly full. The machine has a built-in waste ink absorber to hold the ink used during Print Head cleaning, for example. You can continue printing by selecting "Continue"*1 on the display on your camera. However, because printing is disabled once the waste ink absorber becomes completely full and until the waste ink absorber is replaced, you are recommended to contact the Canon Customer Care Center as early as possible. You will need to replace a particular part of the machine. Low ink level Slow flashing (about three seconds in red) of an ink tank lamp indicates that ink in this tank is low. Prepare a new ink tank. Select "Continue"*1 in the display on your camera to resume printing. Chapter 12 Troubleshooting 129

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Chapter 12
129
Troubleshooting
Error Message On Camera
Action
Printer in use/Printer warming up
Photos are printed from the computer.
Wait until printing ends. When it is ready, the machine starts printing
automatically.
No paper/Paper Error
Load paper in either the Auto Sheet Feeder or Cassette which you have
selected with [Feed Switch] on the machine, and select “Continue”
*1
in
the display on your camera.
The camera does not support the page size that is selected on this
machine. Check the print settings and select the page size that is
supported by the camera.
Open the Paper Output Tray to resume printing. Close the Inner Cover if
it is open. Select “Stop” in the display on your camera to stop printing.
Paper jam
Select “Stop” in the display on your camera to stop printing.
Remove the jammed paper, load new paper, and press [OK] on the machine
and retry printing.
Printer cover open
Close the Scanning Unit (Printer Cover) on the machine.
No print head
The Print Head is defective or not installed.
Install a Print Head according to the
Easy Setup Instructions
.
If the Print Head has already been installed, remove the Print Head and
reinstall it.
If the error still remains, the Print Head may be defective. Contact the
Canon Customer Care Center.
Waste tank (ink absorber) full
This error message indicates that the waste ink absorber is nearly full.
The machine has a built-in waste ink absorber to hold the ink used during
Print Head cleaning, for example. You can continue printing by selecting
“Continue”
*1
on the display on your camera.
However, because printing is disabled once the waste ink absorber
becomes completely full and until the waste ink absorber is replaced, you
are recommended to contact the Canon Customer Care Center as early as
possible. You will need to replace a particular part of the machine.
Low ink level
Slow flashing (about three seconds in red) of an ink tank lamp indicates
that ink in this tank is low. Prepare a new ink tank.
Select “Continue”
*1
in the display on your camera to resume printing.