Cisco VG204 Software Configuration Guide - Page 18

Step 5, Enter the virtual terminal password

Get Cisco VG204 PDF manuals and user guides View all Cisco VG204 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Configuring Global Parameters Chapter 2 Using the setup Command Facility Step 5 Configuring global parameters: Enter hostname [VG]: VG204 The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration. Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when viewing the configuration: Step 6 The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration. Enter enable secret: cisco Enter an enable password that is different from the enable secret password. This password is not encrypted (less secure) and can be seen when viewing the configuration: Step 7 Step 8 The enable password is used when you do not specify an enable secret password, with some older software versions, and some boot images. Enter enable password: cisco % Please choose a password that is different from the enable secret Enter enable password: cisco Enter the virtual terminal password, which prevents unauthenticated access to the VG through ports other than the console port: The virtual terminal password is used to protect access to the VG over a network interface. Enter virtual terminal password: cisco Configure SNMP Network Management? [yes]: n Configure IP? [yes]: Configure RIP routing? [yes]: n Configure bridging? [no]: Respond to the following prompts as appropriate for your network: Do you want to configure FastEthernet0/0 interface? [yes]: Use the 100 Base-TX (RJ-45) connector? [yes]: Operate in full-duplex mode? [no]: Configure IP on this interface? [yes]: IP address for this interface: 9.13.38.150 Subnet mask for this interface [255.0.0.0] : 255.255.255.0 Class A network is 9.0.0.0, 24 subnet bits; mask is /24 Do you want to configure FastEthernet0/1 interface? [yes]: n Would you like to go through AutoSecure configuration? [yes]: n AutoSecure dialog can be started later using "auto secure" CLI The following configuration command script was created: hostname VG-202 enable secret 5 $1$Y0VQ$D8qM6vS3qId.BP3w.GjlE. enable password cisco line vty 0 4 password cisco no snmp-server ! ip routing no bridge 1 Cisco VG202 and Cisco VG204 Voice Gateways Software Configuration Guide 2-4 OL-16191-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
2-4
Cisco VG202 and Cisco VG204 Voice Gateways Software Configuration Guide
OL-16191-01
Chapter 2
Using the setup Command Facility
Configuring Global Parameters
Configuring global parameters:
Enter hostname [VG]:
VG204
The enable secret is a password used to protect access to privileged EXEC and
configuration modes. This password, after entered, becomes encrypted in the configuration.
Step 5
Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when
viewing the configuration:
The enable secret is a password used to protect access to
privileged EXEC and configuration modes. This password, after
entered, becomes encrypted in the configuration.
Enter enable secret:
cisco
Step 6
Enter an enable password that is different from the enable secret password. This password is
not
encrypted (less secure) and can be seen when viewing the configuration:
The enable password is used when you do not specify an
enable secret password, with some older software versions, and
some boot images.
Enter enable password:
cisco
% Please choose a password that is different from the enable secret
Enter enable password:
cisco
Step 7
Enter the virtual terminal password, which prevents unauthenticated access to the VG through ports
other than the console port:
The virtual terminal password is used to protect
access to the VG over a network interface.
Enter virtual terminal password:
cisco
Configure SNMP Network Management? [yes]:
n
Configure IP? [yes]:
Configure RIP routing? [yes]:
n
Configure bridging? [no]:
Step 8
Respond to the following prompts as appropriate for your network:
Do you want to configure FastEthernet0/0
interface? [yes]:
Use the 100 Base-TX (RJ-45) connector? [yes]:
Operate in full-duplex mode? [no]:
Configure IP on this interface? [yes]:
IP address for this interface:
9.13.38.150
Subnet mask for this interface [255.0.0.0] :
255.255.255.0
Class A network is 9.0.0.0, 24 subnet bits; mask is /24
Do you want to configure FastEthernet0/1
interface? [yes]:
n
Would you like to go through AutoSecure configuration? [yes]: n
AutoSecure dialog can be started later using "auto secure" CLI
The following configuration command script was created:
hostname VG-202
enable secret 5 $1$Y0VQ$D8qM6vS3qId.BP3w.GjlE.
enable password cisco
line vty 0 4
password cisco
no snmp-server
!
ip routing
no bridge 1