Cisco VG204 Software Configuration Guide - Page 33

4-7

Cisco VG202 and Cisco VG204 Voice Gateways Software Configuration Guide

OL-16191-01

Chapter 4

Configuring Voice

Configuring the Voice Interface for Cisco CallManager

Configuring the Voice Interface for Cisco CallManager

To configure voice ports to a Cisco Unified Communications Manager server and set various

parameters—including IP address, port number, and version number, use the following commands.

Note

The following steps are required only when the voice interface is configured manually and not through

auto-configuration.

SUMMARY STEPS

1.

enable

2.

configure terminal

3.

stcapp ccm-group

group-id

4.

stcapp

5.

stcapp feature access-code

6.

stcapp feature speed-dial

7.

voice-port

slot-number/port

8.

timeouts initial

seconds

9.

timeouts interdigit

seconds

10.

timeouts ringing

seconds

infinity

11.

voice-port

slot-number/port

12.

ccm-manager fax protocol

[

protocol cisco

]

13.

ccm-manager config

[

server

]

ip-address name seconds

14.

ccm-manager sccp local

interface-type

interface-number

15.

ccm-manager sccp

16.

sccp local

interface-type interface-number

port

port-type

Step 9

ccm-manager config server

tftp_ip_address

Example:

VG(config)# ccm-manager config server tftp

9.13.38.245

Specifies the TFTP server from which the voice gateway

downloads Cisco CallManager XML configuration files

and enables the download of the configuration port

port-number.

Step 10

ccm-manager sccp

Example:

VG(config)# ccm-manager C

Enables Cisco CallManager autoconfiguration of the

Cisco IOS gateway.

Step 11

exit

Example:

VG(config-line)# exit

Exits to global configuration mode.

Command or Action

Purpose

Section	Page
Cisco VG202 and Cisco VG204 Voice Gateways Software Configuration Guide	1
Contents	3
Preface	5
Understanding Interface Numbering and Cisco IOS Software Basics	7
Identifying the Cisco VG202 and Cisco VG204 Voice Gateways	7
Cisco VG202 Voice Gateway	8
Port Numbering Conventions	9
Understanding Cisco IOS Software Basics	10
Getting Help	10
Command Modes	10
Undoing a Command or Feature	11
Saving Configuration Changes	12
Upgrading to a New Cisco IOS Release	12
Cisco VG202 and Cisco VG204 Voice Gateways Deployment Scenario	12
Where to Go Next	13
Using the setup Command Facility	15
Before Powering On Your Cisco Voice Gateway	15
Using the setup Command Facility	16
Configuring Global Parameters	16
Completing the Configuration	19
Configuring with the Command-Line Interface	21
Configuring the Hostname and Password	21
SUMMARY STEPS	22
DETAILED STEPS	22
Verifying the Hostname and Password	23
Configuring Fast Ethernet Interfaces	23
SUMMARY STEPS	24
DETAILED STEPS	24
Example	25
Saving Configuration Changes	25
SUMMARY STEPS	25
DETAILED STEPS	26
Configuring Voice	27
Prerequisites	27
Configuring the Voice Interface	28
Auto-Configuration on the Cisco VG202 and Cisco VG204 Voice Gateways	29
Restrictions for Configuring Auto-Configuration	29
Auto-Configuration With a DHCP Server	30
SUMMARY STEPS	30
DETAILED STEPS	30
Auto-Configuration Without a DHCP Server	31
SUMMARY STEPS	31
DETAILED STEPS	32
Configuring the Voice Interface for Cisco CallManager	33
SUMMARY STEPS	33
DETAILED STEPS	34
Configuring the MAC Address Convention	36
Configuring Calls	37
Call Transfer	37
SUMMARY STEPS	37
DETAILED STEPS	38
Call Waiting	38
Three-Party Conferencing	39
Call ID	39
SUMMARY STEPS	39
DETAILED STEPS	39
Using the ROM Monitor	41
Entering the ROM Monitor Mode	41
SUMMARY STEPS	41
DETAILED STEPS	42
ROM Monitor Commands	42
Command Descriptions	43
Recovering Boot and System Images	44
Using the xmodem Command	44
Configuration Register	44
Changing the Configuration Register Manually	45
Changing the Configuration Register Using Prompts	45
Console Download	46
Command Description	46
Error Reporting	47
Debug Commands	47
Exiting the ROM Monitor	48

Cisco VG204 Software Configuration Guide - Page 33

Configuring the Voice Interface for Cisco CallManager, SUMMARY STEPS - feature access codes

Page 33 highlights