Cisco WS-C1912-A Hardware Installation Guide - Page 48

ISDN BRI Connections, CSU/DSU Connections, Specification, High-Capacitance Cable

Get Cisco WS-C1912-A - Catalyst 1912 Switch PDF manuals and user guides
UPC - 746320021522
View all Cisco WS-C1912-A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Preparing to Connect to a Network Chapter 3 Cable Information and Specifications for Cisco 1900 Series Routers • Synchronous interface-Maximum baud rate is 128 kbps, full-duplex. ISDN BRI Connections The BRI WICs provide Integrated Services Digital Network (ISDN) Basic Rate Interface (BRI) connections. BRI WICs are available with either an S/T interface that requires an external Network Termination 1 (NT1), or a U interface that has a built-in NT1. You can install the BRI WICs in any available WIC slots in the chassis. Warning The ISDN connection is regarded as a source of voltage that should be inaccessible to user contact. Do not attempt to tamper with or open any public telephone operator (PTO)-provided equipment or connection hardware. Any hardwired connection (other than by a nonremovable, connect-one-time-only plug) must be made only by PTO staff or suitably trained engineers. Statement 23 Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first. Statement 1026 Use a BRI cable (not included) to connect the BRI WIC directly to an ISDN. Table 3-3 lists the specifications for ISDN BRI cables. For information about pinouts, refer to the Cisco Modular Access Router Cable Specifications online document, which is located on Cisco.com. Table 3-3 ISDN BRI Cable Specifications Specification Resistance (at 96 kHz) Capacitance (at 1 kHz) Impedance (at 96 kHz) Wire diameter Distance limitation 1. nF = nanofarad High-Capacitance Cable Low-Capacitance Cable 160 ohms/km 120 nF1/km 160 ohms/km 30 nF/km 75 ohms 150 ohms 0.024 in (0.6 mm) 0.024 in (0.6 mm) 32.8 ft (10 m) 32.8 ft (10 m) For more information on BRI WICs, refer to Cisco.com. CSU/DSU Connections CSU/DSU WICs are available that provide switched 56-kbps connections, or full or fractionalized T1 connections. For more information on CSU/DSU WICs, refer to Cisco.com. Cisco 1900 Series Hardware Installation 3-6 OL-19084-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
3-6
Cisco 1900 Series Hardware Installation
OL-19084-01
Chapter 3
Cable Information and Specifications for Cisco 1900 Series Routers
Preparing to Connect to a Network
•
Synchronous interface—Maximum baud rate is 128 kbps, full-duplex.
ISDN BRI Connections
The BRI WICs provide Integrated Services Digital Network (ISDN) Basic Rate Interface (BRI)
connections. BRI WICs are available with either an S/T interface that requires an external Network
Termination 1 (NT1), or a U interface that has a built-in NT1. You can install the BRI WICs in any
available WIC slots in the chassis.
Warning
The ISDN connection is regarded as a source of voltage that should be inaccessible to user contact.
Do not attempt to tamper with or open any public telephone operator (PTO)-provided equipment or
connection hardware. Any hardwired connection (other than by a nonremovable,
connect-one-time-only plug) must be made only by PTO staff or suitably trained engineers.
Statement 23
Warning
Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF
or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables,
detach the end away from the unit first.
Statement 1026
Use a BRI cable (not included) to connect the BRI WIC directly to an ISDN.
Table 3-3
lists the
specifications for ISDN BRI cables. For information about pinouts, refer to the
Cisco Modular Access
Router Cable Specifications
online document, which is located on Cisco.com.
For more information on BRI WICs, refer to Cisco.com.
CSU/DSU Connections
CSU/DSU WICs are available that provide switched 56-kbps connections, or full or fractionalized T1
connections.
For more information on CSU/DSU WICs, refer to Cisco.com.
Table 3-3
ISDN BRI Cable Specifications
Specification
High-Capacitance Cable
Low-Capacitance Cable
Resistance (at 96 kHz)
160 ohms/km
160 ohms/km
Capacitance (at 1 kHz)
120 nF
1
/km
1.
nF = nanofarad
30 nF/km
Impedance (at 96 kHz)
75 ohms
150 ohms
Wire diameter
0.024 in (0.6 mm)
0.024 in (0.6 mm)
Distance limitation
32.8 ft (10 m)
32.8 ft (10 m)