D-Link 502G User Guide - Page 37

PPPoE Connections - login

Get D-Link 502G - DSL Router - EN PDF manuals and user guides View all D-Link 502G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

DSL-502G ADSL Router User's Guide PPPoE Connections Although the connection methods differ significantly, from the viewpoint of the ADSL subscriber, there is little difference between the two variations of PPP connections. The information entered for PPPoE connections is the same as that used for PPPoA connections. Once you have changed the connection method to PPPoE, saved the configuration change and restarted the device, you can proceed to enter authentication information used to connect to the WAN. Follow these steps: Figure 9. Router/Bridge Configuration - PPPoE 1. Under PPPoE Login, enter the Login User Name used for your network account. The user name and login password, are used to authenticate the identity of the ADSL client and provide access to the service provider's network. The user name and login password can be any combination of up to 64 characters. 2. Enter the Login Password. 3. Unless you are instructed to use a different Authentication method, leave the default chap protocol selected. The alternative method, pap, can be selected from the pull-down menu if required by the service provider. Leave the Connect on Demand option as enabled in the pull-down menu. This will allow the Router to establish a WAN connection upon restarting. Leave Idle Time set to the default value 0. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
DSL-502G ADSL Router User’s Guide
25
PPPoE Connections
Although the connection methods differ significantly, from the viewpoint of the ADSL subscriber, there is little
difference between the two variations of PPP connections. The information entered for PPPoE connections is the
same as that used for PPPoA connections.
Once you have changed the connection method to PPPoE, saved the configuration change and restarted the
device, you can proceed to enter authentication information used to connect to the WAN. Follow these steps:
Figure 9. Router/Bridge Configuration - PPPoE
1.
Under
PPPoE Login
, enter the
Login User Name
used for your network account. The user name and
login password, are used to authenticate the identity of the ADSL client and provide access to the
service provider’s network. The user name and login password can be any combination of up to 64
characters.
2.
Enter the Login Password.
3.
Unless you are instructed to use a different
Authentication
method, leave the default
chap
protocol
selected. The alternative method,
pap
, can be selected from the pull-down menu if required by the
service provider.
Leave the
Connect on Demand
option as
enabled
in the pull-down menu. This will allow the Router to
establish a WAN connection upon restarting.
Leave
Idle Time
set to the default value 0.