Dell Alienware Area-51 R4 Service Manual - Page 103

Removing the base panel, Prerequisites, Procedure

Get Dell Alienware Area-51 R4 PDF manuals and user guides View all Dell Alienware Area-51 R4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

Removing the base panel NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Prerequisites 1. Remove the stability foot. 2. Remove the left and right side-panels. See "Removing the side panels". 3. Remove the battery case. 4. Remove the hard drive (HDD1). Procedure CAUTION: If the front bezel and rear bezel have been removed, place the chassis carefully on a flat surface to avoid damaging the I/O ports. 1. Remove the four screws (#6-32x6) that secure the base panel to the chassis. a. screws (4) b. base panel 2. Remove the three screws (#6-32x6) from inside, securing the base panel to the left side of the chassis. 3. Release the tabs from inside the chassis on the left side, securing the base panel to the left side of the chassis. 103

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
Removing the base panel
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow the
steps in
Before working inside your computer
. After working inside your computer, follow the instructions in
After working
inside your computer
. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/
regulatory_compliance
.
Prerequisites
1.
Remove the
stability foot
.
2.
Remove the left and right side-panels. See “
Removing the side panels
”.
3.
Remove the
battery case
.
4.
Remove the
hard drive
(HDD1).
Procedure
CAUTION: If the front bezel and rear bezel have been removed, place the chassis carefully on a flat surface to avoid
damaging the I/O ports.
1.
Remove the four screws (#6-32x6) that secure the base panel to the chassis.
a.
screws (4)
b.
base panel
2.
Remove the three screws (#6-32x6) from inside, securing the base panel to the left side of the chassis.
3.
Release the tabs from inside the chassis on the left side, securing the base panel to the left side of the chassis.
103