Dell Dimension 8400 Owner's Manual - Page 89

Drives, General Installation Guidelines, Connecting Drive Cables - audio

Get Dell Dimension 8400 PDF manuals and user guides View all Dell Dimension 8400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

Drives Your computer supports a combination of these devices: • Up to two hard drives • One optional floppy drive • One optional Zip drive • Up to two CD or DVD drives General Installation Guidelines Connect serial ATA hard drives to the system board connectors labeled SATA-0, SATA-1, SATA-2, or SATA-3. Connect CD/DVD drives to the connector labeled PRI IDE. When you connect two IDE devices to a single IDE interface cable and configure them for the cable select setting, the device attached to the last connector on the interface cable is the primary or the boot device (drive 0), and the device attached to the middle connector on the interface cable is the secondary device (drive 1). See the drive documentation in your upgrade kit for information on configuring devices for the cable select setting. Connecting Drive Cables When you install a drive, you connect two cables-a DC power cable and a data cable-to the back of the drive and to the system board. Some drives may also have an audio connector; one end of the audio cable attaches to the drive connector and the other end attaches to the system board. Drive Interface Connectors Serial ATA Connector interface cable interface connector Removing and Installing Parts 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Removing and Installing Parts
89
Drives
Your computer supports a combination of these devices:
•
Up to two hard drives
•
One optional floppy drive
•
One optional Zip drive
•
Up to two CD or DVD drives
General Installation Guidelines
Connect serial ATA hard drives to the system board connectors labeled SATA-0, SATA-1, SATA-2,
or SATA-3. Connect CD/DVD drives to the connector labeled PRI IDE.
When you connect two IDE devices to a single IDE interface cable and configure them for the
cable select setting, the device attached to the last connector on the interface cable is the primary
or the boot device (drive 0), and the device attached to the middle connector on the interface cable
is the secondary device (drive 1). See the drive documentation in your upgrade kit for information
on configuring devices for the cable select setting.
Connecting Drive Cables
When you install a drive, you connect two cables—a DC power cable and a data cable—to the back
of the drive and to the system board. Some drives may also have an audio connector; one end of the
audio cable attaches to the drive connector and the other end attaches to the system board.
Drive Interface Connectors
Serial ATA Connector
interface cable
interface connector