Dell Latitude CPi A User Manual - Page 10

ZIF Connectors, To reconnect an interface cable to a ZIF connector, perform the following

Get Dell Latitude CPi A PDF manuals and user guides View all Dell Latitude CPi A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Some of the computer's interface connectors are zero insertion force (ZIF) connectors. These connectors are not removable, but they must be released to disconnect a cable from them (see Figure 4). movable part of connector (do not remove) To disconnect an interface cable from a ZIF connector, perform the following steps: 1. Insert a small flat-blade screwdriver under the movable part of the connector. 2. Pull gently upward on the movable part of the connector until it releases the interface cable. 3. Grasp the interface cable and pull it out of the connector. To reconnect an interface cable to a ZIF connector, perform the following steps: 1. Use a small flat-blade screwdriver to open the movable part of the ZIF connector. 2. Orient the end of the interface cable with the ZIF connector, and insert the end of the cable into the connector. 3. While holding the cable in place, close the ZIF connector. To ensure a firm connection, make sure the ZIF connector is completely closed. 4 Dell Latitude CPi A Service Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
4
Dell Latitude CPi A Service Manual
°ËºµÀ¾Â²ż¾»¹
Some of the computer
’
s interface connectors are zero insertion force (ZIF)
connectors. These connectors are not removable, but they must be released
to disconnect a cable from them (see Figure 4).
±²³´µ¶·#¹··$²ÇλÀÀ¶Î¾²À³·ÁÀ·°À¾¶µ"Áζ·ºÁÈɶ
±²³´µ¶·¸ ´Á¿ &µ' ¼Äºº¿¼¾ÄÂÀ ½Â¿ ɽǹſΠ´Ä ½ÌĹ» »½Æ½Ç¿% »Ä ºÄ¾
½ÃÃÅÊ ¾ÄÄ Æ˼Á ÿÀÀË¿ ¾Ä ¾Á¿ ÆÄ̽ÍÅ¿ ý¾ ÄÉ ¾Á¿ ¼Äºº¿¼¾ÄÂÎ
To disconnect an interface cable from a ZIF connector, perform the following
steps:
1.
Insert a small flat-blade screwdriver under the movable part of the
connector.
2.
Pull gently upward on the movable part of the connector until it releases
the interface cable.
3.
Grasp the interface cable and pull it out of the connector.
To reconnect an interface cable to a ZIF connector, perform the following
steps:
1.
Use a small flat-blade screwdriver to open the movable part of the ZIF
connector.
2.
Orient the end of the interface cable with the ZIF connector, and insert the
end of the cable into the connector.
3.
While holding the cable in place, close the ZIF connector.
To ensure a firm connection, make sure the ZIF connector is completely
closed.
movable part of
connector
(do not remove)