Denon AVR 1909 Owners Manual - English - Page 30

Step 3 : Calculation, Step 4 : Check, Step 2 : Measurement

Page 30 highlights

Getting Started Connections Setup Playback Remote Control Multi-zone Information Troubleshooting Specifications ENGLISH Step 2 : Measurement F Menu screen F q Auto Setup q SP2atlnteedpae2sla:eirMsepthaleesaniucigrenhAegtudmmyseipasencotytrsMoiuptlhitooEnnQe.StNleoipws2t:meMenAeaiuasntsugourripASenoudemgsysteiseun2typtniMdounl.tEQ Next Calculate Cancel Front L w Cancel Auto Setup r Audyssey MultEQ Step2:Measurement Auto Setup Please place microphone Audyssey MultEQ at ear height at Step2:Measurement 3rd listening position. All the measurements were finished. Next Calculate Retry Cancel Calculate Retry Cancel q Select "Next 0", then press o. • The measurement of the 2nd position starts. • Select "Calculate 0" with i, and press o to proceed to Step 3. w Move the microphone to the 3rd position and press o. • The measurement of the 3rd position starts. • Select "Calculate 0" with i, and press o to proceed to Step 3. e Perform w repeatedly for the 4th, 5th, and 6th measurments. r "All the measurements were finished." is displayed on the on- screen display. When you have completed measurements in 6 positions. • Select "Calculate 0", and press o to proceed to Step 3. Step 3 : Calculation F Menu screen F q Auto Setup Audyssey MultEQ Step3:Calculation Calculating Please wait... The values obtained from the measurements are automatically analyzed and the attributes for each of the speakers in the listening area are determined. q Select "Calculate 0" at Step 2, then press o. • Analysis begins. • Analysis takes several minutes to complete. • The time required for this analysis depends on the number of speakers connected. The greater the number of speakers connected, the longer analysis will take. NOTE • Do not change the speaker connections or subwoofer volume, or speaker locations after making measurements. If changes are necessary, make the changes and use the Audyssey MultEQ auto setup once again for an updated EQ solution. • For instance, if the location or direction of a speaker is altered, the Auto Setup should be performed again to ensure the correct EQ solution for the new room configuration. Step 4 : Check F Menu screen F q Auto Setup Audyssey MultEQ Step4:Check Please check the results of the measured item. Speaker Config.Check Distance Check Channel Level Check Crossover Freq.Check Next When analysis is complete, check the analysis results for the following four items. q Make your selection using ui and press ENTER. • Presence and size of speaker "Speaker Config. Check" • Distance of speaker from listening position "Distance Check" • Speaker channel level "Channel Level Check" • Crossover Frequency "Crossover Freq. Check" w Use ui to change which speaker is displayed. e Press RETURN. This returns you to analysis results items, so repeat step q. r Press i to select "Next 0", then press o to proceed to Step 5. Distance values that are greater than the actual distance of a speaker may be accurate for speakers with built-in filters (subwoofers, etc). This is because these filters add electrical delay (distance) to the signal that is compensated for by the Auto Setup process. n To cancel Auto Setup Press ui to select "Cancel 0", then press o. After completing a measurement position, move the microphone to the next position. Measure at 6 positions: the main listening position and 5 other surrounding positions. Although it is allowable to measure less than 6 positions, it is recommended to measure 6 for best results. 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92

Specifications
²·
Getting Started
Connections
Setup
Playback
Remote Control
Multi-zone
Information
Troubleshooting
ENGLISH
Step 3 : Calculation
The values obtained from the measurements are automatically
analyzed and the attributes for each of the speakers in the listening
area are determined.
q
Select “Calculate
0
” at Step 2, then press
o
.
• Analysis begins.
• Analysis takes several minutes to complete.
• The time required for this analysis depends on the number of
speakers connected. The greater the number of speakers connected,
the longer analysis will take.
NOTE
• Do not change the speaker connections or subwoofer volume,
or speaker locations after making measurements. If changes are
necessary, make the changes and use the Audyssey MultEQ auto
setup once again for an updated EQ solution.
• For instance, if the location or direction of a speaker is altered, the
Auto Setup should be performed again to ensure the correct EQ
solution for the new room configuration.
Step 4 : Check
Distance values that are greater than the actual distance of a speaker
may be accurate for speakers with built-in filters (subwoofers, etc).
This is because these filters add electrical delay (distance) to the signal
that is compensated for by the Auto Setup process.
When analysis is complete, check the analysis results for the following
four items.
q
Make your selection using
u
i
and press
ENTER
.
• Presence and size of speaker
“Speaker Config. Check”
• Distance of speaker from listening position
“Distance Check”
• Speaker channel level
“Channel Level Check”
• Crossover Frequency
“Crossover Freq. Check”
w
Use
ui
to change which speaker is displayed.
e
Press
RETURN
.
This returns you to analysis results items, so repeat step
q
.
r
Press
i
to select “Next
0
”, then press
o
to proceed to Step 5.
F
Menu screen
F
q
Auto Setup
Step4:Check
Audyssey
MultEQ
Please check the results
of the measured item.
Distance Check
Channel Level Check
Crossover Freq.Check
Speaker Config.Check
Next
Step 2 : Measurement
q
Select “Next
0
”, then press
o
.
• The measurement of the 2nd position starts.
• Select “Calculate
0
” with
i
, and press
o
to proceed to Step 3.
w
Move the microphone to the 3rd position and press
o
.
• The measurement of the 3rd position starts.
• Select “Calculate
0
” with
i
, and press
o
to proceed to Step 3.
e
Perform
w
repeatedly for the 4th, 5th, and 6th measurments.
r
“All the measurements were finished.” is displayed on the on-
screen display. When you have completed measurements in 6
positions.
• Select “Calculate
0
”, and press
o
to proceed to Step 3.
After completing a measurement position, move the microphone to
the next position.
Measure at 6 positions: the main listening position and 5 other
surrounding positions. Although it is allowable to measure less than 6
positions, it is recommended to measure
6
for best results.
F
Menu screen
F
q
q
Auto Setup
Step2:Measurement
Audyssey
MultEQ
Please place microphone
Cancel
Next
Calculate
2nd listening position.
at ear height at
Auto Setup
Step2:Measurement
Audyssey
MultEQ
Now measuring 2nd
Cancel
Front L
listening position.
w
r
Auto Setup
Step2:Measurement
Audyssey
MultEQ
Please place microphone
Retry
Cancel
Next
Calculate
3rd listening position.
at ear height at
Auto Setup
Step2:Measurement
Audyssey
MultEQ
Retry
Cancel
Calculate
All the measurements
were finished.
n
To cancel Auto Setup
Press
ui
to select “Cancel
0
”, then press
o
.
F
Menu screen
F
q
Auto Setup
Step3:Calculation
Audyssey
MultEQ
Calculating
––––––––––––––––––––––––––––––––––––
Please wait...