Electrolux EI30GF55GB Complete Owner's Guide (English) - Page 52

Solutions to Common Problems - reviews

Get Electrolux EI30GF55GB - 30 Inch Gas Range PDF manuals and user guides View all Electrolux EI30GF55GB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

52 Solutions to Common Problems Before you call for service, review the following list. It may save you time & expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance. Problem Appliance is not level Cannot move appliance easily. Appliance must be accessible for service Surface burners do not light Before you call Solution • Be sure floor is level, strong & stable enough to adequately support appliance. • If floor is sagging or sloping, contact a carpenter to correct the situation. • Poor installation. Place oven rack in center of oven. Place a level on the oven rack. Adjust leveling legs at base of appliance until the oven rack is level. • Kitchen cabinet alignment may make appliance appear not level. Be sure cabinets are square & have sufficient room for appliance clearance. • Cabinets not square or are built in too tightly. Contact builder or installer to make appliance accessible. • Carpet interferes with appliance. Provide sufficient space so appliance can be lifted over carpet. • Surface control knob has not been completely turned to (lite). Push in and turn the surface control knob to lite until burner ignites and then turn control knob to desired flame size. • Burner ports are clogged. With the burners OFF, use a small-gauge wire or needle to clean ports. See "Cleaning cooktop and parts" in theCare and Cleaning section for complete instructions. • Appliance power cord is disconnected from outlet. Be sure power cord is securely plugged into the electrical outlet. • Electrical power outage. Surface burner flame burns half way around. • Burner ports are clogged. With the burner OFF, clean ports by using a small-gauge wire or needle. • Moisture is present after cleaning. Lightly fan the flame and allow burner to operate until flame is full. Dry the burners thoroughly and follow instructions under "Cleaning cooktop and parts" in theCare and Cleaning section. Questions or for service call: 1-877-4ELECTORLUX (1-877-435-3287)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
52
Solutions to Common Problems
Before you call for service
,
review the following list. It may save you time & expense. The list includes
common occurrences that are not the result of defective workmanship or materials in this appliance.
Cannot move appliance easily.
Appliance must be accessible for
service
•
Cabinets not square or are built in too tightly. Contact
builder or installer to make appliance accessible.
•
Carpet interferes with appliance. Provide sufficient
space so appliance can be lifted over carpet.
Problem
Solution
Appliance is not level
•
Be sure floor is level, strong & stable enough to
adequately support appliance.
•
If floor is sagging or sloping, contact a carpenter to
correct the situation.
•
Poor installation. Place oven rack in center of oven.
Place a level on the oven rack. Adjust leveling legs at
base of appliance until the oven rack is level.
•
Kitchen cabinet alignment may make appliance appear
not level. Be sure cabinets are square & have sufficient
room for appliance clearance.
Before you call
•
Surface control knob has not been completely turned
to
(lite). Push in and turn the surface control knob to
lite until burner ignites and then turn control knob to
desired flame size.
•
Burner ports are clogged. With the burners OFF, use a
small-gauge wire or needle to clean ports. See
“Cleaning cooktop and parts” in the
Care and Cleaning
section for complete instructions.
•
Appliance power cord is disconnected from outlet. Be
sure power cord is securely plugged into the electrical
outlet.
•
Electrical power outage.
Surface burners do not light
•
Burner ports are clogged. With the burner OFF, clean
ports by using a small-gauge wire or needle.
•
Moisture is present after cleaning. Lightly fan the flame
and allow burner to operate until flame is full. Dry the
burners thoroughly and follow instructions under
“Cleaning cooktop and parts” in the
Care and Cleaning
section.
Surface burner flame burns half way
around.
Questions or for service call:
1-877-4ELECTR
OLUX
(1-877-435-3287)