Epson 6100i Operation Guide - EMP Monitor v4.22 - Page 31

Setting the mail notification function, Select Mail notification function from the Tool, menu.

Get Epson 6100i - PowerLite XGA LCD Projector PDF manuals and user guides
UPC - 010343858176
View all Epson 6100i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Setting the mail notification function 30 The mail notification function can be used to send corresponding notification messages to a preset e-mail address when a projector that is connected to the network assumes a certain status, or if it experiences a problem or warning. By using this function, the operator can be notified of a projector's status or problems even when the operator is in a different location from the projectors. TIP • Up to three addressees (destinations) can be registered and messages can be sent to all of them at once. • If a critical problem develops with a projector which causes it to suddenly stop working, it may not be possible for the projector to send a message notifying an operator of the problem. • If "Standby Mode" is set to "Network ON" or "Network Monitoring" is set to "ON" in the projector configuration menus, you can monitor the projector even when it is in standby mode (when its power is turned off). See your User's Guide for more information. • On some projectors, the mail notification function can be set in the configuration menu. When notification messages are set to be sent in the projector's configuration menu, both the settings in the configuration menu and settings made on EMP Monitor are functional. • Detectable status with the mail notification function differs with the projector you are using. PROCEDURE 1 Select "Mail notification function" from the "Tool" menu. 2 The "Set mail notification function" window will be displayed. Set the following parameters. Mail notification function SMTP server IP address Sender mail address Recipient mail address 1 Recipient mail address 2 Recipient mail address 3 Set to "ON" to use the mail notification function. Enter the IP address of the SMTP server. Up to a maximum of 255 bytes can be entered. When you change a port number of the SMTP server, specify this port number. The default value is "25". You can enter a valid number from 1 to 65535. Enter the sender's e-mail address. Up to a maximum of 255 bytes can be entered. Specify the destination addresses for the notification e-mail. Up to three destinations can be set. Up to a maximum of 255 bytes can be entered.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
30
Setting the mail notification function
The mail notification function can be used to send corresponding notification
messages to a preset e-mail address when a projector that is connected to the
network assumes a certain status, or if it experiences a problem or warning. By
using this function, the operator can be notified of a projector's status or
problems even when the operator is in a different location from the projectors.
PROCEDURE
Select "Mail notification function" from the "Tool"
menu.
The "Set mail notification function" window will be
displayed.
Set the following parameters.
TIP
• Up to three addressees (destinations) can be registered and
messages can be sent to all of them at once.
• If a critical problem develops with a projector which causes it to
suddenly stop working, it may not be possible for the projector to
send a message notifying an operator of the problem.
• If "Standby Mode" is set to "Network ON" or "Network
Monitoring" is set to "ON" in the projector configuration menus,
you can monitor the projector even when it is in standby mode
(when its power is turned off). See your
User’s Guide
for more
information.
• On some projectors, the mail notification function can be set in the
configuration menu. When notification messages are set to be sent
in the projector's configuration menu, both the settings in the
configuration menu and settings made on EMP Monitor are
functional.
• Detectable status with the mail notification function differs with the
projector you are using.
1
Mail notification
function
Set to "ON" to use the mail notification function.
SMTP server
IP address
Enter the IP address of the SMTP server.
Up to a maximum of 255 bytes can be entered.
When you change a port number of the SMTP
server, specify this port number. The default value
is "25".
You can enter a valid number from 1 to 65535.
Sender mail
address
Enter the sender's e-mail address. Up to a
maximum of 255 bytes can be entered.
Recipient
mail address 1
Specify the destination addresses for the
notification e-mail. Up to three destinations can be
set. Up to a maximum of 255 bytes can be entered.
Recipient
mail address 2
Recipient
mail address 3
2