Epson WorkForce 545 Quick Guide - Page 28

Remove the yellow tape from the bottom of - cartridges

Get Epson WorkForce 545 PDF manuals and user guides View all Epson WorkForce 545 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

4. Squeeze the tab on the cartridge and lift it up. Dispose of it carefully. Do not take the used cartridge apart or try to refill it. Warning: If ink gets on your skin, wash it off thoroughly with soap and water. If it gets in your eyes, flush them immediately with water. If you still have discomfort or vision problems, see a doctor immediately. Keep ink cartridges out of the reach of children and don't allow them to drink the ink. 5. Before you open the new cartridge package, shake it gently four or five times. Then remove it from the package. 6. Remove the yellow tape from the bottom of the ink cartridge. Caution: Do not remove any other labels or seals, or ink will leak. Do not touch the green chip on the front of the cartridge. This can damage the ink cartridge. 7. Insert the new ink cartridge into the holder and push it down until it clicks into place. 8. Once you replace all the cartridges that need replacing, close the cartridge cover and push it down until it clicks into place. 9. Close the scanner to begin charging the ink. This takes about 2 1/2 minutes. When you see a completion message on the LCD screen, ink charging is finished. Caution: Never turn off the product while ink is charging or you'll waste ink. If you see an ink replacement message on the LCD screen, press OK and press down all the cartridges securely. Then press OK again. If you remove a low or expended ink cartridge, you cannot reinstall and use the cartridge. 28 Maintaining Your Product

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
28
Maintaining Your Product
4.
Squeeze the tab on the cartridge and lift it up. Dispose
of it carefully. Do not take the used cartridge apart or
try to refill it.
Warning:
If ink gets on your skin, wash it off
thoroughly with soap and water. If it gets in your eyes,
flush them immediately with water. If you still have
discomfort or vision problems, see a doctor
immediately. Keep ink cartridges out of the reach of
children and don’t allow them to drink the ink.
5.
Before you open the new cartridge package, shake it
gently four or five times. Then remove it from the
package.
6.
Remove the yellow tape from the bottom of the
ink cartridge.
Caution:
Do not remove any other labels or
seals, or ink will leak. Do not touch the green
chip on the front of the cartridge. This can
damage the ink cartridge.
7.
Insert the new ink cartridge into the holder and push it down until it clicks into place.
8.
Once you replace all the cartridges that need replacing, close the cartridge cover and
push it down until it clicks into place.
9.
Close the scanner to begin charging the ink. This takes about 2 1/2 minutes. When
you see a completion message on the LCD screen, ink charging is finished.
Caution:
Never turn off the product while ink is charging or you’ll waste ink. If you see
an ink replacement message on the LCD screen, press
OK
and press down all the
cartridges securely. Then press
OK
again. If you remove a low or expended ink
cartridge, you cannot reinstall and use the cartridge.