Harman Kardon AVR 445 Owners Manual - Page 16

ZR 10 REMOTE CONTROL FUNCTIONS å Power Off Button: When used in the room where the AVR 445 is located, press this button to place the unit in Standby. When it is used in a remote room with a sensor that is connected to the Multiroom IR Input Jack e, this button turns the Multiroom system on and off. ∫ OSD Button: Press this button to activate or turn off the On-Screen Display (OSD) menu system, used to set up or adjust the AVR 445's configuration settings. ç AVR Selector Button: Press this button to turn on the AVR 445. The input in use when the unit was last on will be selected. ∂ Input Selectors: When the AVR 445 is off, press one of these buttons to select a specific input and turn the unit on. When the unit is already in use, pressing one of these buttons will change the input. ≠ Tuner Selector: Press this button to select the Tuner as the input source and listen to the tuner band last used. Press the button again to change between AM, FM and, if an XM Connect & Play module is connected and activated, XM Radio. ƒ XM Radio Selector: Press this button to select XM Radio as the input source when an XM Connect & Play module is connected and activated. © Navigation Controls: Depending on the menu or function in use, pressing these buttons will navigate through menus, scroll through option lists or configuration choices, or move the cursor position. Press the left, right, up or down button, as appropriate to the adjustment being made. ˙ Volume Up/Down Buttons: When the ZR 10 remote is used in the room where the AVR 445 is located, press this button to raise or lower the volume in that room. When it is used in a remote room with a sensor that is connected to the Multiroom IR Input Jack e, this button will raise or lower the volume in the remote room. î Disc Skip Buttons: Press these buttons to change discs on compatible Harman Kardon CD or DVD changers or players. ∆ Numeric Keys: Press these buttons to enter a station's frequency or an XM Radio channel number after the Direct Button µ is pressed, or when programming the tuner memories. These buttons may also be used for numeric entries when appropriate with other compatible sources. Blank Buttons: These buttons are not active. Pressing thEem will not change or control any function on the AVR 445 or other IR devices. ¬ Clear Button: When programming the tuner memory, press this button to clear the current entry. µ Direct Button: Press this button when the tuner is in use to start the entry of a station's frequency or an XM channel number for direct access to that station or channel. After pressing this button, press the appropriate Numeric Keys ∆. ñ Memory Button: Press this button to enter a station or XM channel number into the AVR 445's memory. First, tune to, or select, the desired station or channel, and then press this button. Within five seconds, while you see the station or channel flash in the Upper Display Line C and in the on-screen display, press the Numeric Keys ∆ for the preset number between 01 and 30 that you wish to assign to the station or channel. (See page 39 for more information.) ø Tuning Mode Button: When listening to AM or FM stations, press this button to change the tuner mode between manual and automatic. When the button is pressed so that AUTO/STEREO appears in the Upper Display Line C and in the on-screen display, only stations with acceptable signal quality will be tuned, and the tuner will play FM stations in stereo, when available. In the AUTO mode, when the Tuning Up/Down Buttons 3Mπ are pressed, the unit will automatically search for the next available station with good signal strength. When this button is pressed so that MANUAL/MONO appears in the Upper Display Line C and in the on-screen display, each press of the Tuning Up/Down Buttons 3Mπ will move the frequency up or down in single-step increments. When the FM band is in use, pressing the button so that the MANUAL mode is activated will enable you to tune stations with weak signals by changing to monaural reception. (See page 41 for more information on AM/FM tuner operation.) When listing to XM Radio, press this button to scroll through the following display options for the Lower Display Line D: Channel Name ¦ Channel Category ¦ Artist ¦ Title. (See pages 39-40 for more information on XM Radio operation.) π Transport Controls: Press these buttons to control the operation of a compatible Harman Kardon DVD or CD player when the AVR 445 is connected to the source unit via the IR Input Jack F. When the AVR 445's tuner or XM Radio is in use, the Prev/Next Buttons π are used to tune up or down through the list of preset stations, station frequencies or channel numbers. œ Set Button: When using the configuration menus, press this button to enter a setting to the AVR's memory. ® TheBridgeTM Digital Media Player Selector: When Harman Kardon's TheBridgeTM (optional) is connected to TheBridgeTM Digital Media Player (DMP) Input 9 and a compatible iPod is docked in TheBridgeTM , pressing this selector will select the iPod as the audio source input device for the AVR 445. In addition, if a video display is connected to one of the Video Monitor Outputs MP, the iPod's messages will appear on screen, and in the Upper and Lower Display Lines CD. The Buttons ©, the Set Button œ and the Transport Controls π may be used to navigate the iPod and to operate many functions. See page 39, and the manuals for The Bridge and your iPod for more information. ß Mute Button: When the ZR 10 remote is used in the room where the AVR 445 is located, press this button to temporarily silence the unit. When it is used in a remote room with a sensor that is connected to the Multiroom IR Input Jack e, this button will temporarily silence the feed to the remote room only. Press the button again to return to the previous volume level. † IR Transmitter Lens: The infrared code commands from the remote are sent to the AVR from the components behind this lens. To ensure proper operation, do not block this area when holding the remote. 16 ZR 10 REMOTE CONTROL FUNCTIONS