Hayward E-Command 4 Model: ALL MODELS Installation

Hayward E-Command 4 Manual

Get Hayward E-Command 4 PDF manuals and user guides View all Hayward E-Command 4 manuals
Add to My Manuals
Save this manual to your list of manuals

Hayward E-Command 4 manual content summary:

  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 1
    Hayward ECOMMAND 4 Automation Installation Manual for models HPC-4 HPC-4-ACT HPC-4-RC HPC-4-ACT-RC www.haywardnet.com
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 2
    be followed, including the following: • READ AND FOLLOW ALL INSTRUCTIONS • ! WARNING: Disconnect all AC power during installation. • must be connected to the grounding means provided in the electric supply service panel with a continuous copper wire equivalent in size to the circuit conductors
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 3
    2 Optional Base Station 3 Optional Valve Actuators 3 Plumbing Configuration 4 Main Service 5 Grounding and Bonding 5 Circuit Breaker Installation and Wiring 6 General Purpose Outlet 6 ECOMMAND 4 Control Power 6 High Voltage Pool Equipment 7 Low Voltage Wiring 8 Configuration Menu 14
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 4
    hardware (screws, etc.) for mounting ECOMMAND 4 Valves (use standard Hayward, Pentair/Compool, or Jandy valves) Additional valve actuators Accessory Products - Order Separately AQL2-SS-RF Wireless Spa Side Remote Control (Included with HPC-4-RC, HPC-4-ACT-RC) AQL2-BASE-RF Base Station required
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 5
    AQL2-SS-RF Remote Control (included with HPC-4-RC, HPC-4- ACT-RC) The ECOMMAND 4 is compatible with AQL2-SS-RF wireless remote control only. The AQL2-SS-RF is a waterproof portable remote control that is designed to Settings Menu. This information can be found in the ECOMMAND 4 Operation Manual. 2
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 6
    on the upper left side of the ECOMMAND 4 main control unit, insert the base station, and then tighten the nut from the inside. Also refer to the Base Station manual and the diagram on page 13. Optional Valve Actuators (included with HPC-4-ACT, HPC-4-ACT-RC) For optional actuators used with the
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 7
    CHECK VALVE (prevents draining of raised spas) FILTER PUMP MANUAL VALVE MANUAL VALVE POOL VACUUM VALVE TWO-WAY VALVE ENERGY FILTER ISOLATED PRESSURE CLEANER PRESSURE CLEANER Some important notes regarding the ECOMMAND 4 control of Standard Pool/Spa systems: In Pool/Spa Config., select: Pool
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 8
    direct input power to the Control Center. Always: -Ensure that Power is disconnected prior to doing any wiring -Follow all local and NEC (CEC if applicable) codes -Use copper conductors only Main Service (Power to the Circuit Breaker Subpanel) The ECOMMAND 4 circuit breaker subpanel is rated
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 9
    4 enclosure. Per code, the receptacle should be a GFCI type. Alternatively, connect a standard receptacle to a GFCB. ECOMMAND 4 Control Power The ECOMMAND 4 requires 120VAC, 2A power to operate the control logic circuits. This power should be connected to a circuit breaker rated at 125% of the
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 10
    120 VAC Pool Equipment ! WARNING: Do not use the ECOMMAND 4 to control an automatic pool cover. Swimmers may become entrapped underneath the sure to follow the wiring diagram below AND to configure the control logic according to the instructions on page 14. Lo Speed Hi Speed Common Ground 2-Speed
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 11
    for a generic connection. The manuals supplied with most heaters also include specific wiring instructions for connecting the heater to an external control (usually identified as "2-wire" remote control). For millivolt or line voltage heaters, contact Goldline Tech support, 908-355-7995. Refer to
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 12
    Generic Heaters 1. Wire heater to 120/240V power source per the instructions in the heater manual. The ECOMMAND 4 does NOT control the power going to the heater. 2. Wire the ECOMMAND 4 dry contact heater output per the diagram below. Many internal parts of the heater can get very hot--see the heater
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 13
    Hayward Heaters Refer to the instructions in the heater manual for "2-wire Remote Thermostat" operation under "Remote Control Connections" and the diagram below: 1. Turn off power to heater. 2. Wire ECOMMAND 4 to terminals 1 & 2 (see diagram). 3. Leave jumper attached to terminals 4 & 5. 4. Move "
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 14
    homeowners see the "OFF" display and, thinking this is a mistake, change the mode to "POOL" or "SPA" which then disables the remote control by the ECOMMAND 4. To prevent this: Remove the heater touch pad connector (P5) which will disable the touchpad. Black Orange Stripe Orange Black Stripe Light
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 15
    must be set to 001 when using the VSC with the ECOMMAND 4. Refer to the TriStar Pump Owner's Manual (IS3220VSC) and Hayward document IS3220VSCAQLL for specific instructions on setting the pump address. Temperature Sensors The ECOMMAND 4 utilizes 10K ohm thermistor type sensors. Three sensors (water
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 16
    unit. AQL2-BASE-RF Base Receiver Connector for Base Receiver Main PCB Tighten nut Goldline Aqua Rite or Hayward Swimpure Chlorinator The ECOMMAND 4 can control one or more Goldline Aqua Rite or Hayward Swimpure chlorinators when additional sanitizing capacity is required. A 4 wire connection is
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 17
    use of a Goldline Aqua Rite or Hayward Swimpure chlorinator), the ECOMMAND 4 will automatically chlorinate both the pool manual). If disabled (default), all displays relating to the chlorinator will be suppressed. When the chlorinator is enabled, the ECOMMAND 4 will automatically detect and control
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 18
    CountDn This menu will appear only if Pool/Spa Setup is set to "Pool and Spa". This setting is the time, after you manually switch the Pool/Spa valves to "Spa Only", until the ECOMMAND 4 automatically returns the valves to their previous positions. It is programmed in increments of 5 minutes, from
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 19
    If "Pool Only" is selected, then the ECOMMAND 4 will switch the pool/spa valves to the to the appropriate sections in the Installation manual for specific information regarding the control logic for 2speed and variable speed pump operation. For the Hayward Tristar variable speed pump: The Filter
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 20
    pool and plumbed equipment against freeze damage. If freeze protection is enabled and the AIR temperature sensor falls below the freeze threshold (see below), the ECOMMAND 4 will turn on the filter pump to circulate the water. If "Pool and Spa" is selected in the Pool/Spa sub-menu (see page 22
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 21
    the filter pump to turn on, it will only delay the turn off time when solar is operating. Solar Priority If both "Solar Control" and "Heater Control" are enabled, the Solar Priority feature will keep the conventional heater off whenever solar heat is available. This provides the most cost effective
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 22
    relay can be used to control other pool devices that may require these options. The function of each option is shown below. Manual On/Off (default)-the in Operation Manual). The LIGHTS button can also be used to turn the output off. Low Speed of a 2-speed Filter Pump - the ECOMMAND 4 will turn
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 23
    be installed if "Dimmer" is desired. When "Dimmer" is selected, and the Lights output is manually turned on, the "+" and "-" buttons adjust the level from 20% to 100% (default). : Do not use the ECOMMAND 4 to control an automatic pool cover. Swimmers may become entrapped underneath the cover. 20
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 24
    Menu, Operation Manual). The AUX button can also be used to turn the output off. Low Speed of a 2-speed Filter Pump - the ECOMMAND 4 will operate than the desired temperature setting. It is important to note that "Solar Control" must be enabled in the "Solar Config." menu for proper operation to
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 25
    at the times set for the valve3 timeclock in the Timers Menu (see Operations Manual). Solar - the valve operates when the filter pump is running and solar temperature falls sensor falls below the selected freeze temperature threshold, the ECOMMAND 4 will turn on the valve to allow circulation of the
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 26
    . Toggle between 7-day (default) and Weekend/Weekday time options Move to previous/next configuration menu This selection affects ALL of the timeclock logic in the ECOMMAND 4. If "7-day" is selected, each timeclock will have one set of turn-on/turn-off settings that operate every day of the week. If
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 27
    Checkout Follow these instructions to verify that the ECOMMAND 4 is properly controlling the heater. 1. Check that the ECOMMAND 4 is calling jumpers that have to be set correctly for remote control operation-refer to the heater manual and also "Heater Control" (page 8). • Heater is turned on ("Kill
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 28
    . For more detailed instructions on control and operation of the ECOMMAND 4 system, refer to the Operation Manual. Service Mode Service mode disables all automatic control operation and is intended to be used when servicing the pool system. To enter service mode, push the SERVICE button once on the
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 29
    26
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 30
    27
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 31
    and E-Command products to be free of defects in materials and workmanship, under normal use and service for a service center. For more information on authorized service centers please contact the Hayward/Goldline Technical Service Support in the owners manual(s). 5. Problems resulting from tampering
  • Hayward E-Command 4 | Model: ALL MODELS Installation - Page 32
    ECOMMAND 4 Programming Flow Chart default menu settings menu timers menu diagnostic menu scheduled) reason hi-speed is running (not scheduled) countdown time remaining heater control status system manual off check system error filter speed spa heater1 temperature pool heater1 temperature spa
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
Hayward
ECOMMAND 4
Automation
Installation Manual
HPC-4
HPC-4-ACT
HPC-4-RC
HPC-4-ACT-RC
www.haywardnet.com
for models