Hayward OmniLogic Installation Manual - Page 10

Mounting the Equipment - pool controller

Get Hayward OmniLogic PDF manuals and user guides View all Hayward OmniLogic manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

How to Add Salt For new plaster pools, wait 10-14 days before adding salt to allow the plaster to cure. Turn the circulating pump on and add salt directly into the pool. Brush the salt around to speed up the dissolving process-do not allow salt to pile up on the bottom of the pool. Run the filter pump for 24 hours with the suction coming from the main drain (use pool vacuum if there is no main drain) to allow the salt to evenly disperse throughout the pool. The salt display may take 24 hours to respond to the change in salt concentration. Always check stabilizer (cyanuric acid), when checking salt. These levels will most likely decline together. Use the chart below to determine how much stabilizer must be added to raise the level to 40 ppm. Mounting the Equipment OmniLogic Enclosure The OmniLogic is contained in a raintight enclosure that is suitable for outdoor mounting. The control must be mounted a minimum of 6 ft. (2 meters) horizontal distance from the pool/spa (or more, if local codes require). The OmniLogic is designed to mount vertically on a flat surface with the knockouts facing downward. Because the enclosure also acts as a heat sink (disperses heat from inside the box), it is important not to block the four sides of the control. Do not mount the OmniLogic inside a panel or tightly enclosed area. When selecting a location, note that the standard cables supplied with the included flow switch and temperature sensors, as well as optional accessories like Hayward TurboCells and actuators are all 15 ft. (5m) long. The OmniLogic weighs close to 60lbs. and will require two people to position and install. Select the proper location and mounting hardware given the size and weight of the unit. The OmniLogic mounting brackets require a total of 6 mounting bolts to fasten the OmniLogic to the mounting surface. Note that there is a heatsink on the back of the enclosure. Refer to the following information regarding the OmniLogic heatsink: In all cases the heat sink on the back of the OmniLogic panel should not contact the wall behind the panel. This restricts air flow and makes the heat sink less efficient. A minimum separation of 1/8" (except for vinyl siding) should be maintained between any heat sink pin and the siding on the wall behind the enclosure. In the case of a flat wall the mounting flanges on the enclosure ensure that the minimum clearance is maintained. For shingles, clapboards or other siding with a non-flat profile, the installer must ensure the minimum separation. Refer to the diagram on page 7. Special Installation Instructions for Vinyl Siding IMPORTANT: The heat sink on the back of the OmniLogic panel cannot be allowed to contact vinyl siding; during normal chlorinator operation the heat sink pins get warm enough to deform vinyl siding on contact. An increased minimum separation of 3/8" should be maintained between any heat sink pin and the vinyl siding behind the enclosure. 6 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
6
How to Add Salt
For new plaster pools, wait 10-14 days before adding salt to allow the plaster to cure.
Turn the circulating pump on and add salt directly into the pool.
Brush the
salt around to speed up the dissolving process—do not allow salt to pile up on the bottom of the pool.
Run the filter pump for 24 hours with the suction coming
from the main drain (use pool vacuum if there is no main drain) to allow the salt to evenly disperse throughout the pool.
The salt display may take 24 hours to
respond to the change in salt concentration.
Always check stabilizer (cyanuric acid), when checking salt.
These levels will most likely decline together.
Use the chart below to determine how much stabilizer
must be added to raise the level to 40 ppm.
Mounting the Equipment
OmniLogic Enclosure
The OmniLogic is contained in a raintight enclosure that is suitable for outdoor mounting.
The control must be mounted a minimum of 6 ft. (2 meters) horizontal
distance from the pool/spa (or more, if local codes require). The OmniLogic is designed to mount vertically on a flat surface with the knockouts facing downward.
Because the enclosure also acts as a heat sink (disperses heat from inside the box), it is important not to block the four sides of the control.
Do not mount the
OmniLogic inside a panel or tightly enclosed area.
When selecting a location, note that the standard cables supplied with the included flow switch and temperature sensors, as well as optional accessories like
Hayward TurboCells and actuators are all 15 ft. (5m) long.
The OmniLogic weighs close to 60lbs. and will require two people to position and install.
Select the proper location and mounting hardware given the size and
weight of the unit.
The OmniLogic mounting brackets require a total of 6 mounting bolts to fasten the OmniLogic to the mounting surface.
Note that there is a heatsink on the back of the enclosure. Refer to the following information regarding the OmniLogic heatsink:
In all cases the heat sink on the back of the OmniLogic panel should not contact the wall behind the panel. This restricts air flow and makes the heat sink less
efficient. A minimum separation of 1/8” (except for vinyl siding) should be maintained between any heat sink pin and the siding on the wall behind the enclosure.
In the case of a flat wall the mounting flanges on the enclosure ensure that the minimum clearance is maintained.
For shingles, clapboards or other siding with
a non-flat profile, the installer must ensure the minimum separation.
Refer to the diagram on page 7.
Special Installation Instructions for Vinyl Siding
IMPORTANT: The heat sink on the back of the OmniLogic panel cannot be allowed to contact vinyl siding; during normal chlorinator operation the heat sink pins
get warm enough to deform vinyl siding on contact. An increased minimum separation of 3/8” should be maintained between any heat sink pin and the vinyl
siding behind the enclosure.