Hayward OmniLogic Installation Manual - Page 23

Hayward Heaters, Pentair/Purex/MiniMax

Get Hayward OmniLogic PDF manuals and user guides View all Hayward OmniLogic manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Hayward Heaters Refer to the instructions in the heater manual for "2-wire Remote Thermostat" operation under "Remote Control Connections" and the diagram below: 1. Turn off power to heater. 2. Wire OmniLogic to terminals 1 & 2 (see diagram). 3. Leave jumper attached to terminals 4 & 5. 4. Move "BYPASS" dipswitch on heater circuit board to "ON" position (up). 5. Turn heater power back on. 6. Switch heater to either "Pool" or "Spa" (it doesn't make any difference which is selected, the OmniLogic will take control). 7. Heater display should be "bO" (for "bypass On). 8. Heater will fire whenever OmniLogic requests (when OmniLogic "Heater" LED is illuminated). Pentair/Purex/MiniMax 1. Turn power off to heater. 2. Remove factory installed jumper from the "Ext Switch" connector. 3. Wire the OmniLogic to the "Ext Switch" connector as shown below. 4. The wires to the OmniLogic must be separated from any line voltage wires. Failure to follow these instructions may cause erratic operation of the heater. 5. Set the Power (Thermostat Select) switch to either "Pool" or "Spa". 6. Set the "Pool" and "Spa" thermostats to their maximum settings. 19 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
19
Hayward Heaters
Refer to the instructions in the heater manual for “2-wire Remote Thermostat” operation under “Remote Control Connections” and the diagram below:
1.
Turn off power to heater.
2.
Wire OmniLogic to terminals 1 & 2 (see diagram).
3.
Leave jumper attached to terminals 4 & 5.
4.
Move “BYPASS” dipswitch on heater circuit board to “ON” position (up).
5.
Turn heater power back on.
6.
Switch heater to either “Pool” or “Spa” (it doesn’t make any difference which is selected, the OmniLogic will take control).
7.
Heater display should be “bO” (for “bypass On).
8.
Heater will fire whenever OmniLogic requests (when OmniLogic “Heater” LED is illuminated).
Pentair/Purex/MiniMax
1.
Turn power off to heater.
2.
Remove factory installed jumper from the “Ext Switch” connector.
3.
Wire the OmniLogic to the “Ext Switch” connector as shown below.
4.
The wires to the OmniLogic must be separated from any line voltage wires.
Failure to follow these instructions may cause erratic operation of the heater.
5.
Set the Power (Thermostat Select) switch to either “Pool” or “Spa”.
6.
Set the “Pool” and “Spa” thermostats to their maximum settings.